Most GE dryer repairs in Benton involve the same few systems: heat, airflow, the drum drive and the controls. We flag companies whose listing or website mentions GE and fill in with nearby dryer repair companies so you always have options.
This is an independent directory. We are not affiliated with GE, and the technicians listed are independent repair companies, not the manufacturer.
GE Dryer Repair Near Benton
Within 60 miles of Benton there are 19 appliance repair companies in our data. The rest are spread across Centralia (3), Marion (2), and Salem (2). The farthest listed company is about 60 miles out. 3 of them mention GE in their listing or website. Rossin Appliance Services. is the nearest, roughly 13.9 miles from Benton. Rated companies nearby average 4.5 stars across 18 businesses. Benton is a smaller market, so expect a longer drive and ask whether a trip charge applies.
Companies are shown by relevance and distance from Benton. A mention does not mean manufacturer certification, so ask each company about its experience with your dryer.
| With 4.5+ stars and at least 10 reviews | 6 |
|---|---|
| List dryer or washer & dryer work | 9 |
| Repair companies inside 60 miles | 19 |
| Mention GE | 3 |
| Three nearest companies, miles away | 13.9, 16.1, 17.1 |
| Listing Saturday hours | 12 |
At the top of the Benton list: Sears Appliance Repair (56.3 miles away, based in Perryville, 4.6 stars from 132 reviews, lists Saturday hours); Sears Appliance Repair (28.2 miles away, based in Harrisburg, 4.4 stars from 27 reviews, lists Saturday hours); Sears Appliance Repair (40.1 miles away, based in Carmi, 4.6 stars from 13 reviews, lists Saturday hours); Sears Appliance Repair (18.4 miles away, based in Marion, 4.4 stars from 142 reviews, lists Saturday hours).
Know Your GE Dryer
What Makes GE Dryer Repairs Different
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
What GE Says to Check First
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
- Check Vent alert. GE says to unplug the dryer, disconnect and vacuum the duct, and make sure the outside hood damper moves freely. Source: GE Appliances - Dryer - Check Vent Sensor Alert
What GE Dryer Codes Mean
| Code | What it means |
|---|---|
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
When to Call for GE Dryer Repair
- Drum will not turn even though you hear a hum
- Drum turns but the air stays cool
- Dryer will not start when you press Start
What a Dryer Repair Technician Checks
Owner Care for GE Dryers
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
Brand guides: GE Dryer Not Heating: What to Check.
Budgeting for a GE Dryer Repair
A GE dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Gas valve coil replacement (gas dryer): $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Door switch replacement: $50–$150 Source: Fixr - How much does it cost to repair a dryer?
- Drum belt replacement: $150–$250 Source: Fixr - How much does it cost to repair a dryer?
- Drum roller replacement: $100–$150 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair (most homeowners): $100–$430 Source: Angi - How Much Does Dryer Repair Cost?
- Technician labor: $50–$100 per hour Source: Angi - How Much Does Dryer Repair Cost?
A dryer that keeps needing repairs despite regular maintenance is usually cheaper to replace. Source: Angi - How Much Does Dryer Repair Cost?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
What to Have Ready for a GE Dryer Call
- How long the vent run is and where it exits the house
- Any error code on the display
- Whether the dryer is gas or electric
What Benton Owners Should Know
Most dryer calls in Benton come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
In Illinois, you can check a license with the Illinois Department of Public Health Plumber License Search or report a problem to the Illinois Attorney General Consumer Fraud Bureau.
Before You Book in Benton
- Can you give a written estimate before ordering parts?
- Do you work on gas dryers, and who handles anything involving the gas line?
- Will you check the vent and lint path as part of the visit?
GE Dryer Repair FAQs: Benton, IL
How do I find a technician who knows GE dryers?
Why do my clothes come out damp?
Do you work for GE?
Other Dryer Repair in Benton
GE Dryer Repair in Nearby Cities
Clean the lint screen, check the vent hood outside and note the model number before calling. It rules out the simple causes and speeds up a GE repair.