Most GE dryer repairs in Dentsville involve the same few systems: heat, airflow, the drum drive and the controls. Below are independent repair companies serving Dentsville, with those that mention GE first, then the nearest dryer repair companies.
Independent listings only: Washer and Dryer Repair is not affiliated with or endorsed by GE. If your dryer is still under manufacturer coverage, contact GE directly.
GE Dryer Repair Near Dentsville
Our data shows 28 appliance repair companies inside a 30-mile radius of Dentsville. The rest are spread across Columbia (16), Lexington (3), and West Columbia (2). The farthest listed company is about 28 miles out. Of those, 1 mentions GE by name. Sears Appliance Repair is the nearest, roughly 0.7 miles from Dentsville. Rated companies nearby average 4.3 stars across 24 businesses.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| Mention GE | 1 |
|---|---|
| Rated 4.5 stars or higher (10+ reviews) | 11 |
| Open on Saturdays (per listing) | 15 |
| Three nearest companies, miles away | 0.7, 2.4, 3.7 |
| Appliance repair companies in range (30 mi) | 28 |
| Show laundry appliance work | 11 |
At the top of the Dentsville list: Sears Appliance Repair (19.3 miles away, based in Lugoff, 4.3 stars from 46 reviews, lists Saturday hours); Sloan Appliance Service Inc. (9.1 miles away, based in Cayce, 4.7 stars from 2,353 reviews); Appliance Professional (13.6 miles away, based in Lexington, 4.8 stars from 1,369 reviews, lists Saturday hours); Quick Appliance repair llc (9.0 miles away, based in Columbia, 5.0 stars from 241 reviews, lists Saturday hours).
Know Your GE Dryer
What Makes GE Dryer Repairs Different
The GE Profile UltraFast Combo uses a two-stage filter system (a mesh lint filter plus a second mesh or foam filter) located between the display and the dispenser drawers. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
What GE Says to Check First
- Gas dryer runs but does not heat. GE says to confirm a real drying cycle and temperature are selected, keep the front of the dryer unblocked, check the dedicated 120V outlet, and on new installs make sure the gas line is turned on. Source: GE Appliances - Gas Dryer - Runs But Does Not Heat
- Check Vent alert. GE says to unplug the dryer, disconnect and vacuum the duct, and make sure the outside hood damper moves freely. Source: GE Appliances - Dryer - Check Vent Sensor Alert
Reading a GE Dryer Error Code
| Code | What it means |
|---|---|
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
Signs Your GE Dryer Needs a Technician
- Dryer will not start when you press Start
- Outside of the cabinet gets unusually hot
- Dryer shuts off a few minutes into the cycle
What a Dryer Repair Technician Checks
Care GE Recommends for Its Dryers
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
Brand guides: GE Dryer Not Heating: What to Check.
Budgeting for a GE Dryer Repair
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Control board (part only): $90–$280 Source: Angi - How Much Does Dryer Repair Cost?
- Timer replacement: $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Drum belt replacement: $150–$250 Source: Fixr - How much does it cost to repair a dryer?
- Thermostat replacement: $100–$260 Source: Fixr - How much does it cost to repair a dryer?
- Technician labor: $50–$100 per hour Source: Angi - How Much Does Dryer Repair Cost?
A dryer that keeps needing repairs despite regular maintenance is usually cheaper to replace. Source: Angi - How Much Does Dryer Repair Cost?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
What to Have Ready for a GE Dryer Call
- How long the vent run is and where it exits the house
- The brand, model and serial number from the label inside the door or on the back panel
- Any error code on the display
Around Dentsville
Most dryer calls in Dentsville come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
South Carolina does not issue a license specific to appliance repair; mechanical work such as plumbing, heating, air conditioning and refrigeration is licensed by the Contractor's Licensing Board for commercial-scale jobs and by the Residential Builders Commission for residential HVAC and plumbing. Source: S.C. Code Title 40, Chapter 11 (Contractors), South Carolina Legislature
In South Carolina, you can check a license with the SC LLR License Lookup or report a problem to the South Carolina Department of Consumer Affairs.
How to Choose a Dryer Technician Near Dentsville
- If a part has to be ordered, how soon can you come back to finish?
- What is the service call or diagnostic fee, and is it applied to the repair?
- What guarantee do you give on parts and labor?
GE Dryer Repair FAQs: Dentsville, SC
Why does my dryer take so long to dry?
Is my GE dryer worth repairing?
Which Dentsville technicians work on GE?
Other Dryer Repair in Dentsville
More GE Dryer Repair Pages Nearby
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.