Most GE dryer repairs in Killeen involve the same few systems: heat, airflow, the drum drive and the controls. Below are independent repair companies serving Killeen, with those that mention GE first, then the nearest dryer repair companies.
Independent listings only: Washer and Dryer Repair is not affiliated with or endorsed by GE. If your dryer is still under manufacturer coverage, contact GE directly.
Independent GE Dryer Technicians, Killeen TX
28 repair companies serve Killeen from within 30 miles. 8 of them are based in Killeen itself, and the rest are spread across Georgetown (7), Temple (6), and Harker Heights (2). The farthest listed company is about 29 miles out. 1 lists GE specifically. The closest is CSM Electronics, about 1.3 miles away. Across 25 rated companies, the average public rating is 4.0 stars.
Listings come from public business data. A brand or service mention means the company names it in its listing or website; it is not a certification. Verify experience, licensing and insurance before hiring.
| Repair companies inside 30 miles | 28 |
|---|---|
| With 4.5+ stars and at least 10 reviews | 6 |
| Show laundry appliance work | 10 |
| Listing Saturday hours | 17 |
| Distance to the three closest (mi) | 1.3, 1.4, 1.4 |
| Mention GE | 1 |
First up for Killeen: Sears Appliance Repair (24.5 miles away, based in Gatesville, 4.5 stars from 96 reviews, lists Saturday hours); Searle’s Washer & Dryer Repair (17.1 miles away, based in Temple, 4.9 stars from 157 reviews, lists Saturday hours); Appliance Express (29.1 miles away, based in Georgetown, 4.8 stars from 4,508 reviews); Sears Appliance Repair (1.4 miles away, 4.2 stars from 321 reviews, lists Saturday hours).
Know Your GE Dryer
How GE Dryers Are Built
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
Common GE Dryer Problems
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
- Gas dryer runs but does not heat. GE says to confirm a real drying cycle and temperature are selected, keep the front of the dryer unblocked, check the dedicated 120V outlet, and on new installs make sure the gas line is turned on. Source: GE Appliances - Gas Dryer - Runs But Does Not Heat
What GE Dryer Codes Mean
| Code | What it means |
|---|---|
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Dryer will not start when you press Start
- Dryer shuts off a few minutes into the cycle
- Clothes still damp after a full cycle
What a Dryer Repair Technician Checks
Owner Care for GE Dryers
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
- Inspect and clean the exhaust duct at least once a year by unplugging the dryer, disconnecting the duct and vacuuming it, and check that the outside hood flaps move freely with no nests inside. Source: GE Appliances - Dryer - How to Clean Exhaust / Vent Duct
Brand guides: GE Dryer Not Heating: What to Check.
GE Dryer Repair Cost Ranges
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Heating element replacement: $150–$350 Source: Fixr - How much does it cost to repair a dryer?
- Drum bearing replacement: $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Drum belt replacement: $150–$250 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair: $100–$200 Source: Fixr - How much does it cost to repair a dryer?
- Appliance technician diagnosis, washer (usually waived if hired for the repair): $50–$100 per visit Source: Fixr - How much does it cost to repair a washing machine?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Getting Ready for the Repair
- What happens when you press Start (no response, hum, runs with no heat, stops early)
- Any error code on the display
- The brand, model and serial number from the label inside the door or on the back panel
Dryer Notes for Killeen, TX
Most dryer calls in Killeen come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Texas has no separate appliance repair license; under the Plumbing License Law, appliance dealers and their employees may install and service appliances (other than water heaters) without a plumbing license when hooking up to existing openings with a code-approved appliance connector, while other gas or water piping work generally requires a plumbing license. Source: Plumbing License Law, Tex. Occ. Code ch. 1301, §1301.053 (Texas State Board of Plumbing Examiners)
In Texas, you can check a license with the Texas plumbing Public License Search or report a problem to the Texas Attorney General, Consumer Protection Division.
How to Choose a Dryer Technician Near Killeen
- Do you work on gas dryers, and who handles anything involving the gas line?
- How often do you repair GE dryers, and do you carry common parts on the truck?
- If a part has to be ordered, how soon can you come back to finish?
GE Dryer Repair FAQs: Killeen, TX
Why do my clothes come out damp?
How do I find a technician who knows GE dryers?
What makes a dryer stop heating?
Do you work for GE?
More Laundry Repair in Killeen, TX
More GE Dryer Repair Pages Nearby
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.