Most GE dryer repairs in Oak Point involve the same few systems: heat, airflow, the drum drive and the controls. Below are independent repair companies serving Oak Point, with those that mention GE first, then the nearest dryer repair companies.
Washer and Dryer Repair is independent and not affiliated with GE. Listed companies are independent technicians who repair GE dryers and other brands.
GE Dryer Repair Near Oak Point
Our data shows 40 appliance repair companies inside a 30-mile radius of Oak Point. Other nearby bases include Denton (11), Frisco (11), and Lewisville (6). No company within 90 miles of Oak Point mentions GE by name, so these are the nearest appliance repair companies. Most work on several brands, so ask about yours. IAS Appliance Solutions is the nearest, roughly 1.6 miles from Oak Point. Across 34 rated companies, the average public rating is 4.7 stars.
Listings come from public business data. A brand or service mention means the company names it in its listing or website; it is not a certification. Verify experience, licensing and insurance before hiring.
| Mention GE | 0 |
|---|---|
| Show laundry appliance work | 20 |
| With 4.5+ stars and at least 10 reviews | 22 |
| Open on Saturdays (per listing) | 42 |
| Three nearest companies, miles away | 1.6, 3.3, 3.5 |
| Repair companies inside 30 miles | 60 |
First up for Oak Point: Got Your 6 Appliance Repair LLC (8.6 miles away, based in Denton, 5.0 stars from 367 reviews); AGB Appliance Repair (7.1 miles away, based in Denton, 4.8 stars from 636 reviews, lists Saturday hours); J&J Appliance Service (9.3 miles away, based in Denton, 5.0 stars from 495 reviews); Texas True Appliance Repair (8.8 miles away, based in Denton, 5.0 stars from 54 reviews, lists Saturday hours).
Know Your GE Dryer
What a GE Dryer Technician Deals With
The GE Profile UltraFast Combo uses a two-stage filter system (a mesh lint filter plus a second mesh or foam filter) located between the display and the dispenser drawers. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Common GE Dryer Problems
- Dryer will not run or start. GE's first check is that the dryer plug is pushed fully into the wall outlet. Source: GE Appliances - Dryer - Will Not Run or Start
- Check Vent alert. GE says to unplug the dryer, disconnect and vacuum the duct, and make sure the outside hood damper moves freely. Source: GE Appliances - Dryer - Check Vent Sensor Alert
Reading a GE Dryer Error Code
| Code | What it means |
|---|---|
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
Signs Your GE Dryer Needs a Technician
- Cycles take two or three runs to finish
- Outside of the cabinet gets unusually hot
- Clothes still damp after a full cycle
Inside a Dryer Repair Visit
Keeping a GE Dryer Running
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Brand guides: GE Dryer Not Heating: What to Check.
Budgeting for a GE Dryer Repair
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Drum belt replacement: $150–$250 Source: Fixr - How much does it cost to repair a dryer?
- Thermostat replacement: $100–$260 Source: Fixr - How much does it cost to repair a dryer?
- Door switch replacement: $50–$150 Source: Fixr - How much does it cost to repair a dryer?
- Technician labor: $50–$100 per hour Source: Angi - How Much Does Dryer Repair Cost?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
What to Have Ready for a GE Dryer Call
- The brand, model and serial number from the label inside the door or on the back panel
- What happens when you press Start (no response, hum, runs with no heat, stops early)
- Whether the dryer is gas or electric
Dryer Notes for Oak Point, TX
Most dryer calls in Oak Point come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Texas has no separate appliance repair license; under the Plumbing License Law, appliance dealers and their employees may install and service appliances (other than water heaters) without a plumbing license when hooking up to existing openings with a code-approved appliance connector, while other gas or water piping work generally requires a plumbing license. Source: Plumbing License Law, Tex. Occ. Code ch. 1301, §1301.053 (Texas State Board of Plumbing Examiners)
Gas piping counts as plumbing in Texas and requires a plumbing license, with an exemption for LP gas installers who hold a separate state LP gas license. Source: Plumbing License Law, Tex. Occ. Code ch. 1301, §§1301.002, 1301.055 (Texas State Board of Plumbing Examiners)
Before You Book in Oak Point
- Will you check the vent and lint path as part of the visit?
- Is your company licensed where my state requires it, and insured?
- Do you work on gas dryers, and who handles anything involving the gas line?
GE Dryer Repair FAQs: Oak Point, TX
Should I repair or replace my GE dryer?
Why does my dryer take so long to dry?
Why is my dryer running but not heating?
What should I do about a GE error code?
Related Repair Pages for Oak Point
More GE Dryer Repair Pages Nearby
Write down any error code your GE dryer shows and when it appears. It helps a Oak Point technician bring the right parts.