A GE dryer shares most of its parts with other dryers, but its controls, error codes and sensor-dry cycles are specific to the brand. The Show Low list starts with companies that name GE, followed by other appliance repair companies that list dryer work.
Independent listings only: Washer and Dryer Repair is not affiliated with or endorsed by GE. If your dryer is still under manufacturer coverage, contact GE directly.
Independent GE Dryer Technicians, Show Low AZ
We found 5 appliance repair companies within 60 miles of Show Low. 1 list an address in Show Low, and other nearby bases include Pinetop (2), Taylor (1), and Holbrook (1). None of the repair companies near Show Low name GE in their listings, so we show the closest appliance repair companies. Ask each one about your model before booking. Sears Appliance Repair is the nearest, roughly 1.4 miles from Show Low. Across 5 rated companies, the average public rating is 5.0 stars. Because the nearest shops are farther out, ask each company whether Show Low is inside its regular service area.
Listings come from public business data. A brand or service mention means the company names it in its listing or website; it is not a certification. Verify experience, licensing and insurance before hiring.
| Repair companies inside 60 miles | 5 |
|---|---|
| Rated 4.5 stars or higher (10+ reviews) | 2 |
| Open on Saturdays (per listing) | 1 |
| Mention GE | 0 |
| List dryer or washer & dryer work | 2 |
| Three nearest companies, miles away | 1.4, 11.1, 14.3 |
Closest matches for Show Low: Sears Appliance Repair (1.4 miles away, 4.9 stars from 47 reviews, lists Saturday hours); Elite Appliance Repair LLC (11.1 miles away, based in Pinetop, 5.0 stars from 195 reviews); Atlas Appliance Repair Taylor (14.6 miles away, based in Taylor, 5.0 stars from 3 reviews); First Call Appliance Repair (14.3 miles away, based in Pinetop, 5.0 stars from 3 reviews).
GE Dryer Features Technicians Work On
How GE Dryers Are Built
Some GE dryers have an airflow sensor that shows a Check Vent alert when exhaust airflow drops, which usually means the vent is blocked. Source: GE Appliances - Dryer - Check Vent Sensor Alert
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
GE Dryer Symptoms and First Checks
- Gas dryer runs but does not heat. GE says to confirm a real drying cycle and temperature are selected, keep the front of the dryer unblocked, check the dedicated 120V outlet, and on new installs make sure the gas line is turned on. Source: GE Appliances - Gas Dryer - Runs But Does Not Heat
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
GE Dryer Error Codes
| Code | What it means |
|---|---|
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Drum will not turn even though you hear a hum
- Outside of the cabinet gets unusually hot
- Drum turns but the air stays cool
Inside a Dryer Repair Visit
Owner Care for GE Dryers
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Brand guides: GE Dryer Not Heating: What to Check.
Budgeting for a GE Dryer Repair
Price the repair before replacing a GE dryer. Published ranges for common jobs:
- Heating element replacement: $150–$350 Source: Fixr - How much does it cost to repair a dryer?
- Timer replacement: $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Control board (part only): $90–$280 Source: Angi - How Much Does Dryer Repair Cost?
- Drum roller replacement: $100–$150 Source: Fixr - How much does it cost to repair a dryer?
- Technician labor: $50–$100 per hour Source: Angi - How Much Does Dryer Repair Cost?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Before the Technician Arrives
- The brand, model and serial number from the label inside the door or on the back panel
- Any error code on the display
- How long the vent run is and where it exits the house
Around Show Low
Most dryer calls in Show Low come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Arizona has no appliance-repair-specific license; work is regulated through Registrar of Contractors classifications, and state law removes the small-job (under $1,000) handyman exemption for any work connecting or repairing appliances on natural gas or propane. Source: A.R.S. 32-1121 - Persons not required to be licensed
The Arizona Registrar of Contractors licenses gas piping and gas appliance work under its plumbing classifications (such as C-37 and R-37), which cover piping and appliances for natural and manufactured gas. Source: License Classifications - Arizona Registrar of Contractors
Questions to Ask a Show Low Technician
- If a part has to be ordered, how soon can you come back to finish?
- Do you work on gas dryers, and who handles anything involving the gas line?
- What is the service call or diagnostic fee, and is it applied to the repair?
GE Dryer Repair FAQs: Show Low, AZ
Do you work for GE?
Why do my clothes come out damp?
What makes a dryer stop heating?
Is my GE dryer worth repairing?
Related Repair Pages for Show Low
GE Dryer Repair Near Show Low
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.