Most GE dryer repairs in Washington involve the same few systems: heat, airflow, the drum drive and the controls. The Washington list starts with companies that name GE, followed by other appliance repair companies that list dryer work.
Independent listings only: Washer and Dryer Repair is not affiliated with or endorsed by GE. If your dryer is still under manufacturer coverage, contact GE directly.
Independent GE Dryer Technicians, Washington IL
Our data shows 30 appliance repair companies inside a 30-mile radius of Washington. The rest are spread across Bloomington (10), Peoria (8), and Pekin (3). No company within 30 miles of Washington names GE in its listing, so the list adds matches from farther out and the closest appliance repair companies. Fixit is the nearest, roughly 5.3 miles from Washington. Across 25 rated companies, the average public rating is 4.4 stars.
Listings come from public business data. A brand or service mention means the company names it in its listing or website; it is not a certification. Verify experience, licensing and insurance before hiring.
| List dryer or washer & dryer work | 10 |
|---|---|
| Three nearest companies, miles away | 5.3, 6.5, 8.2 |
| Companies within 30 miles | 30 |
| Mention GE | 0 |
| Listing Saturday hours | 21 |
| With 4.5+ stars and at least 10 reviews | 12 |
The leading options for Washington are Sears Appliance Repair (47.7 miles away, based in Peru, 4.4 stars from 70 reviews, lists Saturday hours); Sears Appliance Repair (80.2 miles away, based in Jacksonville, 4.3 stars from 45 reviews, lists Saturday hours); Sears Appliance Repair (10.5 miles away, based in Peoria, 4.6 stars from 270 reviews, lists Saturday hours); Mr. Appliance of Peoria (10.9 miles away, based in Peoria, 4.6 stars from 568 reviews, lists Saturday hours).
Know Your GE Dryer
What Makes GE Dryer Repairs Different
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
What GE Says to Check First
- Dryer will not run or start. GE's first check is that the dryer plug is pushed fully into the wall outlet. Source: GE Appliances - Dryer - Will Not Run or Start
- Check Vent alert. GE says to unplug the dryer, disconnect and vacuum the duct, and make sure the outside hood damper moves freely. Source: GE Appliances - Dryer - Check Vent Sensor Alert
What GE Dryer Codes Mean
| Code | What it means |
|---|---|
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
Signs Your GE Dryer Needs a Technician
- Drum turns but the air stays cool
- Clothes still damp after a full cycle
- Dryer shuts off a few minutes into the cycle
What a Dryer Repair Technician Checks
Keeping a GE Dryer Running
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Brand guides: GE Dryer Not Heating: What to Check.
What GE Dryer Repairs Cost
A GE dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Drum roller replacement: $100–$150 Source: Fixr - How much does it cost to repair a dryer?
- Heating element replacement: $150–$350 Source: Fixr - How much does it cost to repair a dryer?
- Igniter replacement (gas dryer): $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair: $100–$200 Source: Fixr - How much does it cost to repair a dryer?
- Service call fee (may be waived if the technician does the repair): $50–$80 per visit Source: Angi - How Much Does It Cost to Repair a Dryer?
Replacement makes more sense once a dryer is about 10 years old or past half its expected lifespan. Source: Fixr - How much does it cost to repair a dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Getting Ready for the Repair
- How long the vent run is and where it exits the house
- Whether the dryer is gas or electric
- Any error code on the display
Around Washington
Most dryer calls in Washington come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
In Illinois, you can check a license with the Illinois Department of Public Health Plumber License Search or report a problem to the Illinois Attorney General Consumer Fraud Bureau.
Questions to Ask a Washington Technician
- Will you check the vent and lint path as part of the visit?
- What guarantee do you give on parts and labor?
- Can you look at the washer on the same visit if it is acting up too?
GE Dryer Repair FAQs: Washington, IL
What should I do about a GE error code?
How do I find a technician who knows GE dryers?
Do you work for GE?
More Laundry Repair in Washington, IL
More GE Dryer Repair Pages Nearby
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.