A GE dryer shares most of its parts with other dryers, but its controls, error codes and sensor-dry cycles are specific to the brand. Below are independent repair companies serving Revere, with those that mention GE first, then the nearest dryer repair companies.
This is an independent directory. We are not affiliated with GE, and the technicians listed are independent repair companies, not the manufacturer.
Who Works on GE Dryers Near Revere
40 repair companies serve Revere from within 30 miles. 5 list an address in Revere, and other nearby bases include Boston (9), Lynn (5), and Cambridge (5). Distances run up to about 7 miles. ATE Service LLC is the nearest, roughly 0.6 miles from Revere. No company within 30 miles of Revere names GE in its listing, so the list adds matches from farther out and the closest appliance repair companies. The 35 rated companies in range average 4.6 stars.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| List dryer or washer & dryer work | 18 |
|---|---|
| Rated 4.5 stars or higher (10+ reviews) | 29 |
| Three nearest companies, miles away | 0.6, 0.7, 0.8 |
| Companies within 30 miles | 60 |
| Mention GE | 0 |
| Open on Saturdays (per listing) | 45 |
First up for Revere: Sears Appliance Repair (28.1 miles away, based in Newburyport, 4.6 stars from 321 reviews, lists Saturday hours); UltraFix Appliance Repair (7.2 miles away, based in Cambridge, 4.8 stars from 1,527 reviews, lists Saturday hours); Master of Appliances Repair (2.3 miles away, based in Malden, 4.9 stars from 288 reviews); Fasteny Appliance Repair LLC (0.8 miles away, 4.9 stars from 392 reviews, lists Saturday hours).
GE Dryer Lines and Features
How GE Dryers Are Built
Some GE dryers have an airflow sensor that shows a Check Vent alert when exhaust airflow drops, which usually means the vent is blocked. Source: GE Appliances - Dryer - Check Vent Sensor Alert
Common GE Dryer Problems
- Check Vent alert. GE says to unplug the dryer, disconnect and vacuum the duct, and make sure the outside hood damper moves freely. Source: GE Appliances - Dryer - Check Vent Sensor Alert
- Dryer takes too long to dry. GE points first to venting (metal duct, no kinks, clear wall cap) and a clean lint filter, then to load size, dryer level and washer spin speed. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
What GE Dryer Codes Mean
| Code | What it means |
|---|---|
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
Signs Your GE Dryer Needs a Technician
- Burning or hot smell during a cycle
- Drum will not turn even though you hear a hum
- Cycles take two or three runs to finish
What a Dryer Repair Technician Checks
Care GE Recommends for Its Dryers
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Brand guides: GE Dryer Not Heating: What to Check.
What GE Dryer Repairs Cost
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Drum bearing replacement: $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Drive motor replacement: $250–$450 Source: Fixr - How much does it cost to repair a dryer?
- Thermostat replacement: $100–$260 Source: Fixr - How much does it cost to repair a dryer?
- Timer replacement: $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Dryer not heating (repair by symptom): $80–$420 Source: Angi - How Much Does Dryer Repair Cost?
- Service call fee (may be waived if the technician does the repair): $50–$80 per visit Source: Angi - How Much Does It Cost to Repair a Dryer?
Replacement makes more sense once a dryer is about 10 years old or past half its expected lifespan. Source: Fixr - How much does it cost to repair a dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Getting Ready for the Repair
- How long the vent run is and where it exits the house
- What happens when you press Start (no response, hum, runs with no heat, stops early)
- Whether the dryer is gas or electric
Local Notes for Revere
Most dryer calls in Revere come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Massachusetts does not issue a separate appliance repair license; running fuel gas piping to appliances and installing their vent piping is gas fitting work that requires a license from the Board of State Examiners of Plumbers and Gas Fitters. Source: Plumbers and gas fitters consumer fact sheet (Mass.gov)
Gas piping to appliances must be done by a licensed gas fitter or a licensed master or journeyman plumber, under a permit from the local inspector, with licensing by the Board of State Examiners of Plumbers and Gas Fitters. Source: Plumbers and gas fitters consumer fact sheet (Mass.gov)
Hiring a Dryer Repair Company in Revere
- How often do you repair GE dryers, and do you carry common parts on the truck?
- If a part has to be ordered, how soon can you come back to finish?
- Do you work on gas dryers, and who handles anything involving the gas line?
GE Dryer Repair FAQs: Revere, MA
Why do my clothes come out damp?
Is my GE dryer worth repairing?
Is this GE customer service?
More Laundry Repair in Revere, MA
More GE Dryer Repair Pages Nearby
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.