Most GE dryer repairs in Ironwood involve the same few systems: heat, airflow, the drum drive and the controls. Below are independent repair companies serving Ironwood, with those that mention GE first, then the nearest dryer repair companies.
This is an independent directory. We are not affiliated with GE, and the technicians listed are independent repair companies, not the manufacturer.
Who Works on GE Dryers Near Ironwood
6 repair companies serve Ironwood from within 68 miles. The rest are spread across Rhinelander (2), Mercer (1), and Ashland (1). Distances run up to about 67 miles. None of the repair companies near Ironwood name GE in their listings, so we show the closest appliance repair companies. Ask each one about your model before booking. Nearest on the list: Rick"s Appliance Service LLC, around 18.6 miles out. The 6 rated companies in range average 4.6 stars. Ironwood is a smaller market, so expect a longer drive and ask whether a trip charge applies.
Listings come from public business data. A brand or service mention means the company names it in its listing or website; it is not a certification. Verify experience, licensing and insurance before hiring.
| With 4.5+ stars and at least 10 reviews | 3 |
|---|---|
| Repair companies inside 68 miles | 6 |
| Show laundry appliance work | 2 |
| Mention GE | 0 |
| Listing Saturday hours | 2 |
| Three nearest companies, miles away | 18.6, 36.6, 50.2 |
First up for Ironwood: Sears Appliance Repair (67.1 miles away, based in Rhinelander, 4.6 stars from 25 reviews, lists Saturday hours); Rick"s Appliance Service LLC (18.6 miles away, based in Mercer, 5.0 stars from 7 reviews); Bartell Appliance Services (66.5 miles away, based in Rhinelander, 5.0 stars from 2 reviews); Denny's Appliance Service. (50.2 miles away, based in St Germain, 4.8 stars from 21 reviews, lists Saturday hours).
GE Dryer Lines and Features
What Makes GE Dryer Repairs Different
The GE Profile UltraFast Combo uses a two-stage filter system (a mesh lint filter plus a second mesh or foam filter) located between the display and the dispenser drawers. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
Some GE dryers have an airflow sensor that shows a Check Vent alert when exhaust airflow drops, which usually means the vent is blocked. Source: GE Appliances - Dryer - Check Vent Sensor Alert
What GE Says to Check First
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
- Dryer takes too long to dry. GE points first to venting (metal duct, no kinks, clear wall cap) and a clean lint filter, then to load size, dryer level and washer spin speed. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
GE Dryer Error Codes
| Code | What it means |
|---|---|
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Drum turns but the air stays cool
- Cycles take two or three runs to finish
- Dryer shuts off a few minutes into the cycle
What a Dryer Repair Technician Checks
Care GE Recommends for Its Dryers
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Brand guides: GE Dryer Not Heating: What to Check.
Budgeting for a GE Dryer Repair
A GE dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Drum belt replacement: $150–$250 Source: Fixr - How much does it cost to repair a dryer?
- Thermostat replacement: $100–$260 Source: Fixr - How much does it cost to repair a dryer?
- Gas valve coil replacement (gas dryer): $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Dryer not heating (repair by symptom): $80–$420 Source: Angi - How Much Does Dryer Repair Cost?
- Technician service / diagnostic fee, dryer: $50–$80 per visit Source: Fixr - How much does it cost to repair a dryer?
A dryer that keeps needing repairs despite regular maintenance is usually cheaper to replace. Source: Angi - How Much Does Dryer Repair Cost?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Getting Ready for the Repair
- The brand, model and serial number from the label inside the door or on the back panel
- Whether the dryer is gas or electric
- What happens when you press Start (no response, hum, runs with no heat, stops early)
What Ironwood Owners Should Know
Most dryer calls in Ironwood come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Michigan's licensing lists no separate appliance repair license; gas, heating and refrigeration service work is licensed by work classification under the state mechanical contractor license. Source: LARA: Mechanical Examination, Licensing/Registration & Application Information
In Michigan, you can check a license with the LARA Find / Verify a BCC Licensed Professional or Business or report a problem to the Michigan Department of Attorney General, Consumer Protection.
How to Choose a Dryer Technician Near Ironwood
- Will you check the vent and lint path as part of the visit?
- Do you work on gas dryers, and who handles anything involving the gas line?
- Can you look at the washer on the same visit if it is acting up too?
GE Dryer Repair FAQs: Ironwood, MI
Should I repair or replace my GE dryer?
How do I find a technician who knows GE dryers?
Why does my GE dryer show an error code?
Why do my clothes come out damp?
More Laundry Repair in Ironwood, MI
GE Dryer Repair Near Ironwood
Write down any error code your GE dryer shows and when it appears. It helps a Ironwood technician bring the right parts.