Most GE dryer repairs in Bellmead involve the same few systems: heat, airflow, the drum drive and the controls. Below are independent repair companies serving Bellmead, with those that mention GE first, then the nearest dryer repair companies.
This is an independent directory. We are not affiliated with GE, and the technicians listed are independent repair companies, not the manufacturer.
Independent GE Dryer Technicians, Bellmead TX
Our data shows 18 appliance repair companies inside a 30-mile radius of Bellmead. Other nearby bases include Waco (12), Woodway (2), and Hewitt (1). Distances run up to about 28 miles. None of the companies within 30 miles mention GE by name, so we include matching companies from a longer drive plus the nearest appliance repair companies. Nearest on the list: Cen-Tex Services Co, around 1.6 miles out. The 17 rated companies in range average 4.4 stars.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| Three nearest companies, miles away | 1.6, 4.1, 4.4 |
|---|---|
| With 4.5+ stars and at least 10 reviews | 6 |
| Listing Saturday hours | 6 |
| Appliance repair companies in range (30 mi) | 18 |
| List dryer or washer & dryer work | 4 |
| Mention GE | 0 |
Closest matches for Bellmead: Sears Appliance Repair (39.4 miles away, based in Gatesville, 4.5 stars from 96 reviews, lists Saturday hours); Sears Appliance Repair (8.3 miles away, based in Waco, 4.6 stars from 424 reviews, lists Saturday hours); Discount Vacuum & Appliance (6.3 miles away, based in Waco, 4.3 stars from 372 reviews, lists Saturday hours); Mr. Appliance of Waco (11.4 miles away, based in Woodway, 4.6 stars from 365 reviews).
GE Dryer Lines and Features
What a GE Dryer Technician Deals With
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
What GE Says to Check First
- Check Vent alert. GE says to unplug the dryer, disconnect and vacuum the duct, and make sure the outside hood damper moves freely. Source: GE Appliances - Dryer - Check Vent Sensor Alert
- Dryer takes too long to dry. GE points first to venting (metal duct, no kinks, clear wall cap) and a clean lint filter, then to load size, dryer level and washer spin speed. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Reading a GE Dryer Error Code
| Code | What it means |
|---|---|
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
When to Call for GE Dryer Repair
- Dryer shuts off a few minutes into the cycle
- Cycles take two or three runs to finish
- Drum will not turn even though you hear a hum
What Gets Fixed on a Bellmead Dryer Call
Care GE Recommends for Its Dryers
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
Brand guides: GE Dryer Not Heating: What to Check.
Budgeting for a GE Dryer Repair
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Drum roller replacement: $100–$150 Source: Fixr - How much does it cost to repair a dryer?
- Thermal fuse repair: $80–$130 Source: Angi - How Much Does It Cost to Repair a Dryer?
- Gas valve coil replacement (gas dryer): $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Technician service / diagnostic fee, dryer: $50–$80 per visit Source: Fixr - How much does it cost to repair a dryer?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Before the Technician Arrives
- The brand, model and serial number from the label inside the door or on the back panel
- Any error code on the display
- What happens when you press Start (no response, hum, runs with no heat, stops early)
Dryer Notes for Bellmead, TX
Most dryer calls in Bellmead come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Texas has no separate appliance repair license; under the Plumbing License Law, appliance dealers and their employees may install and service appliances (other than water heaters) without a plumbing license when hooking up to existing openings with a code-approved appliance connector, while other gas or water piping work generally requires a plumbing license. Source: Plumbing License Law, Tex. Occ. Code ch. 1301, §1301.053 (Texas State Board of Plumbing Examiners)
Gas piping counts as plumbing in Texas and requires a plumbing license, with an exemption for LP gas installers who hold a separate state LP gas license. Source: Plumbing License Law, Tex. Occ. Code ch. 1301, §§1301.002, 1301.055 (Texas State Board of Plumbing Examiners)
Hiring a Dryer Repair Company in Bellmead
- What guarantee do you give on parts and labor?
- Will you check the vent and lint path as part of the visit?
- Is your company licensed where my state requires it, and insured?
GE Dryer Repair FAQs: Bellmead, TX
Do you work for GE?
Why does my GE dryer show an error code?
Why do my clothes come out damp?
What makes a dryer stop heating?
Other Dryer Repair in Bellmead
GE Dryer Repair in Nearby Cities
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.