If your GE dryer has stopped heating, stopped tumbling or started throwing an error code, the technician you call should know the model line. Below are independent repair companies serving Southlake, with those that mention GE first, then the nearest dryer repair companies.
Washer and Dryer Repair is independent and not affiliated with GE. Listed companies are independent technicians who repair GE dryers and other brands.
GE Dryer Repair Near Southlake
40 repair companies serve Southlake from within 30 miles. 4 of them are based in Southlake itself, and other nearby bases include Hurst (6), Keller (4), and Grapevine (4). Nearest on the list: Excellence Appliance Repair, around 1.0 miles out. No company within 90 miles of Southlake mentions GE by name, so these are the nearest appliance repair companies. Most work on several brands, so ask about yours. The 34 rated companies in range average 4.4 stars.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| Appliance repair companies in range (30 mi) | 60 |
|---|---|
| Mention GE | 0 |
| Distance to the three closest (mi) | 1.0, 1.4, 1.6 |
| With 4.5+ stars and at least 10 reviews | 25 |
| Show laundry appliance work | 23 |
| Open on Saturdays (per listing) | 44 |
At the top of the Southlake list: Ace Refrigeration and Appliance Repair (2.8 miles away, based in Keller, 4.9 stars from 1,857 reviews); ProStar Appliance LLC (8.2 miles away, based in Euless, 4.8 stars from 214 reviews, lists Saturday hours); Solution Appliance Repair (1.4 miles away, 5.0 stars from 62 reviews, lists Saturday hours); Appliance Repair Now (1.6 miles away, 4.8 stars from 230 reviews).
GE Dryer Features Technicians Work On
How GE Dryers Are Built
GE allows only rigid or flexible metal vent duct and says plastic flexible duct is not acceptable because it collapses, cuts airflow and can collect water. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Common GE Dryer Problems
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
GE Dryer Error Codes
| Code | What it means |
|---|---|
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Drum will not turn even though you hear a hum
- Cycles take two or three runs to finish
- Squealing, thumping or grinding while it runs
How a Dryer Service Call Usually Goes in Southlake
Keeping a GE Dryer Running
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Brand guides: GE Dryer Not Heating: What to Check.
GE Dryer Repair Cost Ranges
A GE dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Control board (part only): $90–$280 Source: Angi - How Much Does Dryer Repair Cost?
- Heating element replacement: $150–$350 Source: Fixr - How much does it cost to repair a dryer?
- Door switch replacement: $50–$150 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair: $100–$200 Source: Fixr - How much does it cost to repair a dryer?
- Technician labor: $50–$100 per hour Source: Angi - How Much Does Dryer Repair Cost?
A dryer that keeps needing repairs despite regular maintenance is usually cheaper to replace. Source: Angi - How Much Does Dryer Repair Cost?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Getting Ready for the Repair
- What happens when you press Start (no response, hum, runs with no heat, stops early)
- Whether the dryer is gas or electric
- Any error code on the display
Around Southlake
Most dryer calls in Southlake come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Texas has no separate appliance repair license; under the Plumbing License Law, appliance dealers and their employees may install and service appliances (other than water heaters) without a plumbing license when hooking up to existing openings with a code-approved appliance connector, while other gas or water piping work generally requires a plumbing license. Source: Plumbing License Law, Tex. Occ. Code ch. 1301, §1301.053 (Texas State Board of Plumbing Examiners)
Gas piping counts as plumbing in Texas and requires a plumbing license, with an exemption for LP gas installers who hold a separate state LP gas license. Source: Plumbing License Law, Tex. Occ. Code ch. 1301, §§1301.002, 1301.055 (Texas State Board of Plumbing Examiners)
Hiring a Dryer Repair Company in Southlake
- Can you look at the washer on the same visit if it is acting up too?
- Is your company licensed where my state requires it, and insured?
- What is the service call or diagnostic fee, and is it applied to the repair?
GE Dryer Repair FAQs: Southlake, TX
Do you work for GE?
What should I do about a GE error code?
What makes a dryer stop heating?
Is my GE dryer worth repairing?
Related Repair Pages for Southlake
GE Dryer Repair in Nearby Cities
Clean the lint screen, check the vent hood outside and note the model number before calling. It rules out the simple causes and speeds up a GE repair.