A GE dryer shares most of its parts with other dryers, but its controls, error codes and sensor-dry cycles are specific to the brand. Below are independent repair companies serving Victoria, with those that mention GE first, then the nearest dryer repair companies.
Independent listings only: Washer and Dryer Repair is not affiliated with or endorsed by GE. If your dryer is still under manufacturer coverage, contact GE directly.
Independent GE Dryer Technicians, Victoria TX
Within 60 miles of Victoria there are 13 appliance repair companies in our data. 3 of them are based in Victoria itself, and the rest are spread across Beeville (3), Rockport (3), and El Campo (2). No company within 60 miles of Victoria names GE in its listing, so the list adds matches from farther out and the closest appliance repair companies. Appliance Pro is the nearest, roughly 0.8 miles from Victoria. Across 13 rated companies, the average public rating is 4.1 stars. Victoria is a smaller market, so expect a longer drive and ask whether a trip charge applies.
Listings come from public business data. A brand or service mention means the company names it in its listing or website; it is not a certification. Verify experience, licensing and insurance before hiring.
| Show laundry appliance work | 4 |
|---|---|
| Mention GE | 0 |
| Three nearest companies, miles away | 0.8, 1.5, 2.6 |
| Repair companies inside 60 miles | 13 |
| Open on Saturdays (per listing) | 7 |
| Rated 4.5 stars or higher (10+ reviews) | 3 |
Closest matches for Victoria: Sears Appliance Repair (74.5 miles away, based in La Grange, 4.7 stars from 61 reviews, lists Saturday hours); Sears Appliance Repair (2.6 miles away, 4.1 stars from 214 reviews, lists Saturday hours); Elite Appliance Repair (1.5 miles away, 4.7 stars from 85 reviews); Appliance Pro (0.8 miles away, 4.7 stars from 160 reviews, lists Saturday hours).
GE Dryer Features Technicians Work On
How GE Dryers Are Built
The GE Profile UltraFast Combo uses a two-stage filter system (a mesh lint filter plus a second mesh or foam filter) located between the display and the dispenser drawers. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
GE Dryer Symptoms and First Checks
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
What GE Dryer Codes Mean
| Code | What it means |
|---|---|
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
When to Call for GE Dryer Repair
- Dryer shuts off a few minutes into the cycle
- Dryer will not start when you press Start
- Clothes still damp after a full cycle
How a Dryer Service Call Usually Goes in Victoria
Owner Care for GE Dryers
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Brand guides: GE Dryer Not Heating: What to Check.
What GE Dryer Repairs Cost
Price the repair before replacing a GE dryer. Published ranges for common jobs:
- Heating element replacement: $150–$350 Source: Fixr - How much does it cost to repair a dryer?
- Drum bearing replacement: $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Control board (part only): $90–$280 Source: Angi - How Much Does Dryer Repair Cost?
- Thermostat replacement: $100–$260 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair: $100–$200 Source: Fixr - How much does it cost to repair a dryer?
- Technician service / diagnostic fee, dryer: $50–$80 per visit Source: Fixr - How much does it cost to repair a dryer?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Before the Technician Arrives
- What happens when you press Start (no response, hum, runs with no heat, stops early)
- How long the vent run is and where it exits the house
- Any error code on the display
Dryer Notes for Victoria, TX
Most dryer calls in Victoria come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Texas has no separate appliance repair license; under the Plumbing License Law, appliance dealers and their employees may install and service appliances (other than water heaters) without a plumbing license when hooking up to existing openings with a code-approved appliance connector, while other gas or water piping work generally requires a plumbing license. Source: Plumbing License Law, Tex. Occ. Code ch. 1301, §1301.053 (Texas State Board of Plumbing Examiners)
Gas piping counts as plumbing in Texas and requires a plumbing license, with an exemption for LP gas installers who hold a separate state LP gas license. Source: Plumbing License Law, Tex. Occ. Code ch. 1301, §§1301.002, 1301.055 (Texas State Board of Plumbing Examiners)
How to Choose a Dryer Technician Near Victoria
- Is your company licensed where my state requires it, and insured?
- Do you work on gas dryers, and who handles anything involving the gas line?
- Can you give a written estimate before ordering parts?
GE Dryer Repair FAQs: Victoria, TX
Is this GE customer service?
Why does my GE dryer show an error code?
Which Victoria technicians work on GE?
More Laundry Repair in Victoria, TX
GE Dryer Repair Near Victoria
Clean the lint screen, check the vent hood outside and note the model number before calling. It rules out the simple causes and speeds up a GE repair.