A GE dryer shares most of its parts with other dryers, but its controls, error codes and sensor-dry cycles are specific to the brand. Below are independent repair companies serving Radford, with those that mention GE first, then the nearest dryer repair companies.
Washer and Dryer Repair is independent and not affiliated with GE. Listed companies are independent technicians who repair GE dryers and other brands.
Independent GE Dryer Technicians, Radford VA
33 repair companies serve Radford from within 60 miles. The rest are spread across Roanoke (9), Princeton (3), and Christiansburg (2). The farthest listed company is about 60 miles out. The closest is Sears Appliance Repair, about 8.4 miles away. 2 list GE specifically. The 30 rated companies in range average 3.8 stars. Because the nearest shops are farther out, ask each company whether Radford is inside its regular service area.
Companies are shown by relevance and distance from Radford. A mention does not mean manufacturer certification, so ask each company about its experience with your dryer.
| Repair companies inside 60 miles | 33 |
|---|---|
| Show laundry appliance work | 7 |
| Rated 4.5 stars or higher (10+ reviews) | 7 |
| Distance to the three closest (mi) | 8.4, 8.4, 17.1 |
| Mention GE | 2 |
| Listing Saturday hours | 12 |
The leading options for Radford are Sears Appliance Repair (55.5 miles away, based in Covington, 4.4 stars from 42 reviews, lists Saturday hours); GE Appliance Services (35.5 miles away, based in Roanoke, 1.0 stars from 6 reviews, lists Saturday hours); Sears Appliance Repair (8.4 miles away, based in Christiansburg, 4.3 stars from 159 reviews, lists Saturday hours); Peerless Appliance Services (37.5 miles away, based in Roanoke, 4.9 stars from 1,204 reviews).
GE Dryer Lines and Features
How GE Dryers Are Built
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
GE allows only rigid or flexible metal vent duct and says plastic flexible duct is not acceptable because it collapses, cuts airflow and can collect water. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Common GE Dryer Problems
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
- Dryer will not run or start. GE's first check is that the dryer plug is pushed fully into the wall outlet. Source: GE Appliances - Dryer - Will Not Run or Start
What GE Dryer Codes Mean
| Code | What it means |
|---|---|
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
Signs Your GE Dryer Needs a Technician
- Squealing, thumping or grinding while it runs
- Dryer shuts off a few minutes into the cycle
- Outside of the cabinet gets unusually hot
What a Dryer Repair Technician Checks
Keeping a GE Dryer Running
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
Brand guides: GE Dryer Not Heating: What to Check.
Budgeting for a GE Dryer Repair
A GE dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Thermal fuse repair: $80–$130 Source: Angi - How Much Does It Cost to Repair a Dryer?
- Drum bearing replacement: $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Control board (part only): $90–$280 Source: Angi - How Much Does Dryer Repair Cost?
- Typical dryer repair: $100–$200 Source: Fixr - How much does it cost to repair a dryer?
- Appliance technician diagnosis, washer (usually waived if hired for the repair): $50–$100 per visit Source: Fixr - How much does it cost to repair a washing machine?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Before the Technician Arrives
- Any error code on the display
- What happens when you press Start (no response, hum, runs with no heat, stops early)
- The brand, model and serial number from the label inside the door or on the back panel
What Radford Owners Should Know
Most dryer calls in Radford come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Virginia's Board for Contractors has no appliance repair license classification, but its gas fitting contracting specialty covers installing, repairing or removing gas piping and appliances attached to real property. Source: 18VAC50-22-30, Definitions of specialty services
The Board for Contractors licenses gas fitting contractors and individual gas fitter, natural gas fitter and liquefied petroleum gas fitter tradesmen. Source: 18VAC50-30-10, Definitions (Individual License and Certification Regulations)
Hiring a Dryer Repair Company in Radford
- Do you work on gas dryers, and who handles anything involving the gas line?
- Will you check the vent and lint path as part of the visit?
- If a part has to be ordered, how soon can you come back to finish?
GE Dryer Repair FAQs: Radford, VA
Is my GE dryer worth repairing?
Why does my dryer take so long to dry?
What should I do about a GE error code?
Other Dryer Repair in Radford
GE Dryer Repair in Nearby Cities
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.