If your GE dryer has stopped heating, stopped tumbling or started throwing an error code, the technician you call should know the model line. Below are independent repair companies serving Enterprise, with those that mention GE first, then the nearest dryer repair companies.
Independent listings only: Washer and Dryer Repair is not affiliated with or endorsed by GE. If your dryer is still under manufacturer coverage, contact GE directly.
Who Works on GE Dryers Near Enterprise
Within 60 miles of Enterprise there are 12 appliance repair companies in our data. 2 list an address in Enterprise, and the rest are spread across Dothan (3), Eufaula (3), and Newton (1). Sears Appliance Repair is the nearest, roughly 0.9 miles from Enterprise. No company within 60 miles of Enterprise names GE in its listing, so the list adds matches from farther out and the closest appliance repair companies. Across 12 rated companies, the average public rating is 4.5 stars. Enterprise is a smaller market, so expect a longer drive and ask whether a trip charge applies.
Companies are shown by relevance and distance from Enterprise. A mention does not mean manufacturer certification, so ask each company about its experience with your dryer.
| Mention GE | 0 |
|---|---|
| Open on Saturdays (per listing) | 4 |
| Distance to the three closest (mi) | 0.9, 1.1, 14.7 |
| Show laundry appliance work | 5 |
| With 4.5+ stars and at least 10 reviews | 6 |
| Companies within 60 miles | 12 |
First up for Enterprise: Sears Appliance Repair (88.0 miles away, based in Monroeville, 4.6 stars from 60 reviews, lists Saturday hours); Tri-State Appliance Repair (1.1 miles away, 4.4 stars from 47 reviews); Sears Appliance Repair (0.9 miles away, 4.5 stars from 208 reviews, lists Saturday hours); Mr. Appliance of Dothan (14.7 miles away, based in Newton, 4.6 stars from 261 reviews).
GE Dryer Lines and Features
What a GE Dryer Technician Deals With
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Common GE Dryer Problems
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
- Gas dryer runs but does not heat. GE says to confirm a real drying cycle and temperature are selected, keep the front of the dryer unblocked, check the dedicated 120V outlet, and on new installs make sure the gas line is turned on. Source: GE Appliances - Gas Dryer - Runs But Does Not Heat
Reading a GE Dryer Error Code
| Code | What it means |
|---|---|
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
Signs Your GE Dryer Needs a Technician
- Dryer will not start when you press Start
- Clothes still damp after a full cycle
- Cycles take two or three runs to finish
What a Dryer Repair Technician Checks
Owner Care for GE Dryers
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Brand guides: GE Dryer Not Heating: What to Check.
What GE Dryer Repairs Cost
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Drum bearing replacement: $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Door switch replacement: $50–$150 Source: Fixr - How much does it cost to repair a dryer?
- Drum belt replacement: $150–$250 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair: $100–$200 Source: Fixr - How much does it cost to repair a dryer?
- Technician labor: $50–$100 per hour Source: Angi - How Much Does Dryer Repair Cost?
A dryer that keeps needing repairs despite regular maintenance is usually cheaper to replace. Source: Angi - How Much Does Dryer Repair Cost?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Before the Technician Arrives
- How long the vent run is and where it exits the house
- The brand, model and serial number from the label inside the door or on the back panel
- Whether the dryer is gas or electric
Dryer Notes for Enterprise, AL
Most dryer calls in Enterprise come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Alabama does not issue a separate appliance repair license, and the state's heating, air conditioning and refrigeration contractor law expressly excludes work on household appliances, residential refrigerators and ice machines. Source: Code of Alabama 1975, Section 34-31-18 et seq. (Alabama Board of Heating, Air Conditioning & Refrigeration Contractors)
Gas fitting work in Alabama requires a state gas fitter license from the Alabama Plumbers and Gas Fitters Examining Board, which tests competency before anyone performs, supervises or contracts gas fitting. Source: About the Board - Alabama Plumbers and Gas Fitters Examining Board
Before You Book in Enterprise
- Can you give a written estimate before ordering parts?
- How often do you repair GE dryers, and do you carry common parts on the truck?
- Is your company licensed where my state requires it, and insured?
GE Dryer Repair FAQs: Enterprise, AL
What should I do about a GE error code?
Why is my dryer running but not heating?
How do I find a technician who knows GE dryers?
Why do my clothes come out damp?
Related Repair Pages for Enterprise
More GE Dryer Repair Pages Nearby
Write down any error code your GE dryer shows and when it appears. It helps a Enterprise technician bring the right parts.