Most GE dryer repairs in Blackhawk involve the same few systems: heat, airflow, the drum drive and the controls. We flag companies whose listing or website mentions GE and fill in with nearby dryer repair companies so you always have options.
This is an independent directory. We are not affiliated with GE, and the technicians listed are independent repair companies, not the manufacturer.
Who Works on GE Dryers Near Blackhawk
Our data shows 40 appliance repair companies inside a 30-mile radius of Blackhawk. The rest are spread across Walnut Creek (10), Concord (8), and San Ramon (7). Distances run up to about 11 miles. No company within 90 miles of Blackhawk mentions GE by name, so these are the nearest appliance repair companies. Most work on several brands, so ask about yours. The closest is Danville Appliance Repair, about 1.3 miles away. Across 30 rated companies, the average public rating is 4.8 stars.
Companies are shown by relevance and distance from Blackhawk. A mention does not mean manufacturer certification, so ask each company about its experience with your dryer.
| Repair companies inside 30 miles | 60 |
|---|---|
| Three nearest companies, miles away | 1.3, 3.4, 4.1 |
| Rated 4.5 stars or higher (10+ reviews) | 14 |
| Listing Saturday hours | 34 |
| Show laundry appliance work | 9 |
| Mention GE | 0 |
Closest matches for Blackhawk: Sears Appliance Repair (10.1 miles away, based in Concord, 4.6 stars from 471 reviews, lists Saturday hours); ADRIUM service solutions (4.5 miles away, based in San Ramon, 5.0 stars from 187 reviews, lists Saturday hours); VOLTA Heating, Air Conditioning & Appliance Services (4.2 miles away, based in San Ramon, 5.0 stars from 116 reviews, lists Saturday hours); White Crow Repair (10.0 miles away, based in Concord, 4.5 stars from 43 reviews, lists Saturday hours).
GE Dryer Lines and Features
How GE Dryers Are Built
The GE Profile UltraFast Combo uses a two-stage filter system (a mesh lint filter plus a second mesh or foam filter) located between the display and the dispenser drawers. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
What GE Says to Check First
- Dryer will not run or start. GE's first check is that the dryer plug is pushed fully into the wall outlet. Source: GE Appliances - Dryer - Will Not Run or Start
- Check Vent alert. GE says to unplug the dryer, disconnect and vacuum the duct, and make sure the outside hood damper moves freely. Source: GE Appliances - Dryer - Check Vent Sensor Alert
What GE Dryer Codes Mean
| Code | What it means |
|---|---|
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Dryer will not start when you press Start
- Drum turns but the air stays cool
- Cycles take two or three runs to finish
How a Dryer Service Call Usually Goes in Blackhawk
Keeping a GE Dryer Running
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Brand guides: GE Dryer Not Heating: What to Check.
What GE Dryer Repairs Cost
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Control board (part only): $90–$280 Source: Angi - How Much Does Dryer Repair Cost?
- Gas valve coil replacement (gas dryer): $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Drum bearing replacement: $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Technician service / diagnostic fee, dryer: $50–$80 per visit Source: Fixr - How much does it cost to repair a dryer?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Getting Ready for the Repair
- How long the vent run is and where it exits the house
- What happens when you press Start (no response, hum, runs with no heat, stops early)
- The brand, model and serial number from the label inside the door or on the back panel
What Blackhawk Owners Should Know
Most dryer calls in Blackhawk come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
California requires businesses that repair major home appliances such as refrigerators, ranges, dishwashers, washers and dryers for pay to register with the Bureau of Household Goods and Services as Major Home Appliance Service Dealers, including out-of-state providers serving California customers. Source: Application for Registration (Electronic and Appliance Repair Dealers) - Bureau of Household Goods and Services
Gas piping, gas appliance connections and gas safety devices fall within the C-36 Plumbing Contractor classification licensed by the Contractors State License Board. Source: C-36 - Plumbing Contractor, Licensing Classifications Detail - CSLB
Hiring a Dryer Repair Company in Blackhawk
- Do you work on gas dryers, and who handles anything involving the gas line?
- Can you give a written estimate before ordering parts?
- Is your company licensed where my state requires it, and insured?
GE Dryer Repair FAQs: Blackhawk, CA
Why does my GE dryer show an error code?
Should I repair or replace my GE dryer?
Why does my dryer take so long to dry?
Do you work for GE?
Other Dryer Repair in Blackhawk
More GE Dryer Repair Pages Nearby
Clean the lint screen, check the vent hood outside and note the model number before calling. It rules out the simple causes and speeds up a GE repair.