A GE dryer shares most of its parts with other dryers, but its controls, error codes and sensor-dry cycles are specific to the brand. We flag companies whose listing or website mentions GE and fill in with nearby dryer repair companies so you always have options.
Washer and Dryer Repair is independent and not affiliated with GE. Listed companies are independent technicians who repair GE dryers and other brands.
Who Works on GE Dryers Near Anna
22 repair companies serve Anna from within 60 miles. 1 of them are based in Anna itself, and other nearby bases include Paducah (7), Marion (2), and Carbondale (1). The farthest listed company is about 59 miles out. 2 list GE specifically. The closest is Riley'sl,., about 1.3 miles away. Across 21 rated companies, the average public rating is 4.2 stars. Anna is a smaller market, so expect a longer drive and ask whether a trip charge applies.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| Open on Saturdays (per listing) | 13 |
|---|---|
| Three nearest companies, miles away | 1.3, 18.9, 20.4 |
| Companies within 60 miles | 22 |
| Mention GE | 2 |
| Show laundry appliance work | 9 |
| Rated 4.5 stars or higher (10+ reviews) | 5 |
Closest matches for Anna: Sears Appliance Repair (40.0 miles away, based in Perryville, 4.6 stars from 132 reviews, lists Saturday hours); Sears Appliance Repair (43.7 miles away, based in Harrisburg, 4.4 stars from 27 reviews, lists Saturday hours); Sears Appliance Repair (71.5 miles away, based in Carmi, 4.6 stars from 13 reviews, lists Saturday hours); Sears Appliance Repair (20.4 miles away, based in Cape Girardeau, 4.5 stars from 146 reviews, lists Saturday hours).
Know Your GE Dryer
How GE Dryers Are Built
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
GE Dryer Symptoms and First Checks
- Dryer takes too long to dry. GE points first to venting (metal duct, no kinks, clear wall cap) and a clean lint filter, then to load size, dryer level and washer spin speed. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
- Dryer will not run or start. GE's first check is that the dryer plug is pushed fully into the wall outlet. Source: GE Appliances - Dryer - Will Not Run or Start
GE Dryer Error Codes
| Code | What it means |
|---|---|
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Burning or hot smell during a cycle
- Cycles take two or three runs to finish
- Dryer shuts off a few minutes into the cycle
What Gets Fixed on a Anna Dryer Call
Care GE Recommends for Its Dryers
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
Brand guides: GE Dryer Not Heating: What to Check.
GE Dryer Repair Cost Ranges
Price the repair before replacing a GE dryer. Published ranges for common jobs:
- Drum belt replacement: $150–$250 Source: Fixr - How much does it cost to repair a dryer?
- Control board (part only): $90–$280 Source: Angi - How Much Does Dryer Repair Cost?
- Drive motor replacement: $250–$450 Source: Fixr - How much does it cost to repair a dryer?
- Heating element replacement: $150–$350 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair: $100–$200 Source: Fixr - How much does it cost to repair a dryer?
- Technician labor: $50–$100 per hour Source: Angi - How Much Does Dryer Repair Cost?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
What to Have Ready for a GE Dryer Call
- Any error code on the display
- The brand, model and serial number from the label inside the door or on the back panel
- Whether the dryer is gas or electric
Around Anna
Most dryer calls in Anna come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
In Illinois, you can check a license with the Illinois Department of Public Health Plumber License Search or report a problem to the Illinois Attorney General Consumer Fraud Bureau.
How to Choose a Dryer Technician Near Anna
- How often do you repair GE dryers, and do you carry common parts on the truck?
- Will you check the vent and lint path as part of the visit?
- Can you look at the washer on the same visit if it is acting up too?
GE Dryer Repair FAQs: Anna, IL
Is my GE dryer worth repairing?
What makes a dryer stop heating?
Why does my GE dryer show an error code?
Other Dryer Repair in Anna
GE Dryer Repair Near Anna
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.