If your GE dryer has stopped heating, stopped tumbling or started throwing an error code, the technician you call should know the model line. The Baltimore list starts with companies that name GE, followed by other appliance repair companies that list dryer work.
Washer and Dryer Repair is independent and not affiliated with GE. Listed companies are independent technicians who repair GE dryers and other brands.
GE Dryer Repair Near Baltimore
Our data shows 40 appliance repair companies inside a 30-mile radius of Baltimore. 23 list an address in Baltimore, and the rest are spread across Parkville (4), Towson (3), and Dundalk (2). The farthest listed company is about 10 miles out. No company within 30 miles of Baltimore names GE in its listing, so the list adds matches from farther out and the closest appliance repair companies. Nearest on the list: UltraFix Appliance Repair, around 0.4 miles out. The 35 rated companies in range average 4.2 stars.
Companies are shown by relevance and distance from Baltimore. A mention does not mean manufacturer certification, so ask each company about its experience with your dryer.
| Show laundry appliance work | 15 |
|---|---|
| Three nearest companies, miles away | 0.4, 1.0, 1.0 |
| Rated 4.5 stars or higher (10+ reviews) | 23 |
| Mention GE | 0 |
| Companies within 30 miles | 60 |
| Listing Saturday hours | 41 |
Closest matches for Baltimore: District-Columbia Hotpoint Rpr (36.2 miles away, based in Washington, 5.0 stars from 4 reviews, lists Saturday hours); Landers Appliance (6.9 miles away, 4.9 stars from 2,398 reviews); All-Star Appliance Repair Baltimore (6.0 miles away, 4.7 stars from 1,459 reviews, lists Saturday hours); Racz Appliance Repair (5.5 miles away, based in Parkville, 4.4 stars from 139 reviews, lists Saturday hours).
GE Dryer Lines and Features
How GE Dryers Are Built
GE allows only rigid or flexible metal vent duct and says plastic flexible duct is not acceptable because it collapses, cuts airflow and can collect water. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
What GE Says to Check First
- Dryer will not run or start. GE's first check is that the dryer plug is pushed fully into the wall outlet. Source: GE Appliances - Dryer - Will Not Run or Start
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
What GE Dryer Codes Mean
| Code | What it means |
|---|---|
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
When to Call for GE Dryer Repair
- Burning or hot smell during a cycle
- Dryer shuts off a few minutes into the cycle
- Drum will not turn even though you hear a hum
What Gets Fixed on a Baltimore Dryer Call
Keeping a GE Dryer Running
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Brand guides: GE Dryer Not Heating: What to Check.
GE Dryer Repair Cost Ranges
Price the repair before replacing a GE dryer. Published ranges for common jobs:
- Door switch replacement: $50–$150 Source: Fixr - How much does it cost to repair a dryer?
- Gas valve coil replacement (gas dryer): $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Drum bearing replacement: $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Drum roller replacement: $100–$150 Source: Fixr - How much does it cost to repair a dryer?
- Technician service / diagnostic fee, dryer: $50–$80 per visit Source: Fixr - How much does it cost to repair a dryer?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
What to Have Ready for a GE Dryer Call
- How long the vent run is and where it exits the house
- What happens when you press Start (no response, hum, runs with no heat, stops early)
- Whether the dryer is gas or electric
What Baltimore Owners Should Know
Most dryer calls in Baltimore come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Maryland does not issue a separate appliance repair license; the Maryland Board of Plumbing licenses plumbers, natural gas fitters and propane gas fitters, whose trades cover gas connections. Source: License Requirements - Maryland Board of Plumbing (Maryland Department of Labor)
The Maryland Board of Plumbing issues master, journey and apprentice natural gas fitter licenses and a propane gas fitter certificate, and recognizes certain Baltimore County and WSSC gas fitter licenses. Source: Md. Code, Business Occupations and Professions ยง 12-302 (Maryland General Assembly)
Before You Book in Baltimore
- Is your company licensed where my state requires it, and insured?
- Can you give a written estimate before ordering parts?
- Will you check the vent and lint path as part of the visit?
GE Dryer Repair FAQs: Baltimore, MD
Why does my GE dryer show an error code?
Should I repair or replace my GE dryer?
Do you work for GE?
Related Repair Pages for Baltimore
More GE Dryer Repair Pages Nearby
Clean the lint screen, check the vent hood outside and note the model number before calling. It rules out the simple causes and speeds up a GE repair.