If your GE dryer has stopped heating, stopped tumbling or started throwing an error code, the technician you call should know the model line. Below are independent repair companies serving Harper Woods, with those that mention GE first, then the nearest dryer repair companies.
Independent listings only: Washer and Dryer Repair is not affiliated with or endorsed by GE. If your dryer is still under manufacturer coverage, contact GE directly.
Who Works on GE Dryers Near Harper Woods
Our data shows 40 appliance repair companies inside a 30-mile radius of Harper Woods. Other nearby bases include Detroit (7), Clinton Township (6), and Warren (5). The farthest listed company is about 12 miles out. Sears Appliance Repair is the nearest, roughly 2.0 miles from Harper Woods. No company within 90 miles of Harper Woods mentions GE by name, so these are the nearest appliance repair companies. Most work on several brands, so ask about yours. Rated companies nearby average 4.3 stars across 35 businesses.
Companies are shown by relevance and distance from Harper Woods. A mention does not mean manufacturer certification, so ask each company about its experience with your dryer.
| Rated 4.5 stars or higher (10+ reviews) | 21 |
|---|---|
| Show laundry appliance work | 22 |
| Listing Saturday hours | 44 |
| Distance to the three closest (mi) | 2.0, 2.1, 2.2 |
| Mention GE | 0 |
| Companies within 30 miles | 60 |
First up for Harper Woods: Detroit Appliance (6.2 miles away, based in Fraser, 4.8 stars from 1,139 reviews, lists Saturday hours); Sargent Appliance (8.7 miles away, based in Clinton Township, 4.8 stars from 690 reviews, lists Saturday hours); AJ's Appliance Repair & HVAC (7.7 miles away, based in Fraser, 4.6 stars from 1,181 reviews); Mr. Appliance of Macomb County (11.3 miles away, based in Mt Clemens, 4.8 stars from 245 reviews).
Know Your GE Dryer
What Makes GE Dryer Repairs Different
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
Common GE Dryer Problems
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
- Gas dryer runs but does not heat. GE says to confirm a real drying cycle and temperature are selected, keep the front of the dryer unblocked, check the dedicated 120V outlet, and on new installs make sure the gas line is turned on. Source: GE Appliances - Gas Dryer - Runs But Does Not Heat
GE Dryer Error Codes
| Code | What it means |
|---|---|
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Cycles take two or three runs to finish
- Dryer will not start when you press Start
- Clothes still damp after a full cycle
Inside a Dryer Repair Visit
Owner Care for GE Dryers
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Brand guides: GE Dryer Not Heating: What to Check.
Budgeting for a GE Dryer Repair
Price the repair before replacing a GE dryer. Published ranges for common jobs:
- Timer replacement: $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Drum roller replacement: $100–$150 Source: Fixr - How much does it cost to repair a dryer?
- Igniter replacement (gas dryer): $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair: $100–$200 Source: Fixr - How much does it cost to repair a dryer?
- Service call fee (may be waived if the technician does the repair): $50–$80 per visit Source: Angi - How Much Does It Cost to Repair a Dryer?
A dryer that keeps needing repairs despite regular maintenance is usually cheaper to replace. Source: Angi - How Much Does Dryer Repair Cost?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
What to Have Ready for a GE Dryer Call
- Any error code on the display
- Whether the dryer is gas or electric
- What happens when you press Start (no response, hum, runs with no heat, stops early)
What Harper Woods Owners Should Know
Most dryer calls in Harper Woods come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Michigan's licensing lists no separate appliance repair license; gas, heating and refrigeration service work is licensed by work classification under the state mechanical contractor license. Source: LARA: Mechanical Examination, Licensing/Registration & Application Information
Gas piping work is licensed by the state through mechanical contractor specialty classifications, including fuel gas piping, fuel gas piping and venting, and LP distribution piping. Source: LARA: Mechanical Examination, Licensing/Registration & Application Information
Questions to Ask a Harper Woods Technician
- Will you check the vent and lint path as part of the visit?
- Is your company licensed where my state requires it, and insured?
- Do you work on gas dryers, and who handles anything involving the gas line?
GE Dryer Repair FAQs: Harper Woods, MI
Should I repair or replace my GE dryer?
How do I find a technician who knows GE dryers?
Why does my dryer take so long to dry?
Other Dryer Repair in Harper Woods
GE Dryer Repair in Nearby Cities
Clean the lint screen, check the vent hood outside and note the model number before calling. It rules out the simple causes and speeds up a GE repair.