A GE dryer shares most of its parts with other dryers, but its controls, error codes and sensor-dry cycles are specific to the brand. Below are independent repair companies serving Center Line, with those that mention GE first, then the nearest dryer repair companies.
Independent listings only: Washer and Dryer Repair is not affiliated with or endorsed by GE. If your dryer is still under manufacturer coverage, contact GE directly.
Independent GE Dryer Technicians, Center Line MI
Within 30 miles of Center Line there are 40 appliance repair companies in our data. The rest are spread across Detroit (8), Warren (5), and Madison Heights (4). The farthest listed company is about 10 miles out. Nearest on the list: XT Appliances, around 0.9 miles out. No company within 90 miles of Center Line mentions GE by name, so these are the nearest appliance repair companies. Most work on several brands, so ask about yours. Across 33 rated companies, the average public rating is 4.4 stars.
Companies are shown by relevance and distance from Center Line. A mention does not mean manufacturer certification, so ask each company about its experience with your dryer.
| Distance to the three closest (mi) | 0.9, 1.3, 1.4 |
|---|---|
| Open on Saturdays (per listing) | 44 |
| Rated 4.5 stars or higher (10+ reviews) | 21 |
| Companies within 30 miles | 60 |
| Show laundry appliance work | 22 |
| Mention GE | 0 |
First up for Center Line: Detroit Appliance (5.0 miles away, based in Fraser, 4.8 stars from 1,139 reviews, lists Saturday hours); Sargent Appliance (8.8 miles away, based in Clinton Township, 4.8 stars from 690 reviews, lists Saturday hours); AJ's Appliance Repair & HVAC (5.9 miles away, based in Fraser, 4.6 stars from 1,181 reviews); Sears Appliance Repair (2.9 miles away, based in Warren, 4.6 stars from 448 reviews, lists Saturday hours).
Know Your GE Dryer
How GE Dryers Are Built
Some GE dryers have an airflow sensor that shows a Check Vent alert when exhaust airflow drops, which usually means the vent is blocked. Source: GE Appliances - Dryer - Check Vent Sensor Alert
The GE Profile UltraFast Combo uses a two-stage filter system (a mesh lint filter plus a second mesh or foam filter) located between the display and the dispenser drawers. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
What GE Says to Check First
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
- Dryer will not run or start. GE's first check is that the dryer plug is pushed fully into the wall outlet. Source: GE Appliances - Dryer - Will Not Run or Start
What GE Dryer Codes Mean
| Code | What it means |
|---|---|
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Dryer will not start when you press Start
- Outside of the cabinet gets unusually hot
- Drum turns but the air stays cool
What a Dryer Repair Technician Checks
Care GE Recommends for Its Dryers
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Brand guides: GE Dryer Not Heating: What to Check.
GE Dryer Repair Cost Ranges
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Gas valve coil replacement (gas dryer): $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Drum bearing replacement: $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Thermostat replacement: $100–$260 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair: $100–$200 Source: Fixr - How much does it cost to repair a dryer?
- Technician labor: $50–$100 per hour Source: Angi - How Much Does Dryer Repair Cost?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Getting Ready for the Repair
- What happens when you press Start (no response, hum, runs with no heat, stops early)
- How long the vent run is and where it exits the house
- The brand, model and serial number from the label inside the door or on the back panel
What Center Line Owners Should Know
Most dryer calls in Center Line come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Michigan's licensing lists no separate appliance repair license; gas, heating and refrigeration service work is licensed by work classification under the state mechanical contractor license. Source: LARA: Mechanical Examination, Licensing/Registration & Application Information
Gas piping work is licensed by the state through mechanical contractor specialty classifications, including fuel gas piping, fuel gas piping and venting, and LP distribution piping. Source: LARA: Mechanical Examination, Licensing/Registration & Application Information
Questions to Ask a Center Line Technician
- If a part has to be ordered, how soon can you come back to finish?
- Will you check the vent and lint path as part of the visit?
- How often do you repair GE dryers, and do you carry common parts on the truck?
GE Dryer Repair FAQs: Center Line, MI
How do I find a technician who knows GE dryers?
Why do my clothes come out damp?
Should I repair or replace my GE dryer?
Related Repair Pages for Center Line
More GE Dryer Repair Pages Nearby
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.