A GE dryer shares most of its parts with other dryers, but its controls, error codes and sensor-dry cycles are specific to the brand. The Angier list starts with companies that name GE, followed by other appliance repair companies that list dryer work.
Washer and Dryer Repair is independent and not affiliated with GE. Listed companies are independent technicians who repair GE dryers and other brands.
Independent GE Dryer Technicians, Angier NC
Our data shows 40 appliance repair companies inside a 30-mile radius of Angier. 2 of them are based in Angier itself, and other nearby bases include Raleigh (12), Cary (6), and Fuquay-Varina (4). Distances run up to about 22 miles. 1 of them mentions GE in their listing or website. Appliance Depot is the nearest, roughly 0.3 miles from Angier. Rated companies nearby average 4.2 stars across 38 businesses.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| Show laundry appliance work | 14 |
|---|---|
| Three nearest companies, miles away | 0.3, 4.9, 5.3 |
| Open on Saturdays (per listing) | 38 |
| Mention GE | 1 |
| Rated 4.5 stars or higher (10+ reviews) | 26 |
| Repair companies inside 30 miles | 60 |
Closest matches for Angier: Sears Appliance Repair (15.4 miles away, based in Dunn, 4.6 stars from 128 reviews, lists Saturday hours); JNJ Dryer Vent Cleaning (11.9 miles away, based in Holly Springs, 5.0 stars from 3,144 reviews); Mr. Appliance of Cary (17.8 miles away, based in Cary, 4.9 stars from 1,970 reviews, lists Saturday hours); One Source Appliance Repair (9.3 miles away, based in Holly Springs, 4.7 stars from 239 reviews).
GE Dryer Features Technicians Work On
What Makes GE Dryer Repairs Different
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
What GE Says to Check First
- Dryer will not run or start. GE's first check is that the dryer plug is pushed fully into the wall outlet. Source: GE Appliances - Dryer - Will Not Run or Start
- Check Vent alert. GE says to unplug the dryer, disconnect and vacuum the duct, and make sure the outside hood damper moves freely. Source: GE Appliances - Dryer - Check Vent Sensor Alert
Reading a GE Dryer Error Code
| Code | What it means |
|---|---|
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
Signs Your GE Dryer Needs a Technician
- Cycles take two or three runs to finish
- Squealing, thumping or grinding while it runs
- Dryer will not start when you press Start
How a Dryer Service Call Usually Goes in Angier
Keeping a GE Dryer Running
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Brand guides: GE Dryer Not Heating: What to Check.
What GE Dryer Repairs Cost
Price the repair before replacing a GE dryer. Published ranges for common jobs:
- Gas valve coil replacement (gas dryer): $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Drive motor replacement: $250–$450 Source: Fixr - How much does it cost to repair a dryer?
- Thermal fuse repair: $80–$130 Source: Angi - How Much Does It Cost to Repair a Dryer?
- Drum belt replacement: $150–$250 Source: Fixr - How much does it cost to repair a dryer?
- Dryer not heating (repair by symptom): $80–$420 Source: Angi - How Much Does Dryer Repair Cost?
- Appliance technician diagnosis, washer (usually waived if hired for the repair): $50–$100 per visit Source: Fixr - How much does it cost to repair a washing machine?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Before the Technician Arrives
- Any error code on the display
- What happens when you press Start (no response, hum, runs with no heat, stops early)
- Whether the dryer is gas or electric
Local Notes for Angier
Most dryer calls in Angier come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
North Carolina has no license specific to appliance repair; work on gas appliances, fuel piping and heating equipment is regulated by the State Board of Examiners of Plumbing, Heating, and Fire Sprinkler Contractors, with an exemption for minor repairs that don't change fuel type, venting or piping. Source: N.C. Gen. Stat. § 87-21 (NC General Assembly)
Gas and fuel piping installation requires a plumbing or heating license, or a restricted fuel piping license, issued by the State Board of Examiners of Plumbing, Heating, and Fire Sprinkler Contractors. Source: N.C. Gen. Stat. § 87-21 (NC General Assembly)
Questions to Ask a Angier Technician
- Will you check the vent and lint path as part of the visit?
- Is your company licensed where my state requires it, and insured?
- Do you work on gas dryers, and who handles anything involving the gas line?
GE Dryer Repair FAQs: Angier, NC
Is my GE dryer worth repairing?
Why does my dryer take so long to dry?
Is this GE customer service?
Other Dryer Repair in Angier
GE Dryer Repair Near Angier
Write down any error code your GE dryer shows and when it appears. It helps a Angier technician bring the right parts.