Most GE dryer repairs in Asheville involve the same few systems: heat, airflow, the drum drive and the controls. The Asheville list starts with companies that name GE, followed by other appliance repair companies that list dryer work.
Washer and Dryer Repair is independent and not affiliated with GE. Listed companies are independent technicians who repair GE dryers and other brands.
GE Dryer Repair Near Asheville
Within 30 miles of Asheville there are 29 appliance repair companies in our data. 10 list an address in Asheville, and the rest are spread across Hendersonville (5), Waynesville (3), and Brevard (3). The farthest listed company is about 30 miles out. No company within 30 miles of Asheville names GE in its listing, so the list adds matches from farther out and the closest appliance repair companies. Nearest on the list: Justice Appliance Repair, around 1.6 miles out. The 29 rated companies in range average 4.5 stars.
Listings come from public business data. A brand or service mention means the company names it in its listing or website; it is not a certification. Verify experience, licensing and insurance before hiring.
| Open on Saturdays (per listing) | 13 |
|---|---|
| Appliance repair companies in range (30 mi) | 29 |
| Show laundry appliance work | 5 |
| Mention GE | 0 |
| Distance to the three closest (mi) | 1.6, 1.6, 1.7 |
| Rated 4.5 stars or higher (10+ reviews) | 16 |
First up for Asheville: Sears Appliance Repair (67.3 miles away, based in Kingsport, 4.5 stars from 174 reviews, lists Saturday hours); Mr. Appliance of Asheville (9.9 miles away, based in Fletcher, 4.8 stars from 1,708 reviews, lists Saturday hours); Sears Appliance Repair (1.7 miles away, 4.5 stars from 193 reviews, lists Saturday hours); Sears Appliance Repair (25.1 miles away, based in Waynesville, 4.6 stars from 182 reviews, lists Saturday hours).
GE Dryer Features Technicians Work On
What a GE Dryer Technician Deals With
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
What GE Says to Check First
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
- Dryer takes too long to dry. GE points first to venting (metal duct, no kinks, clear wall cap) and a clean lint filter, then to load size, dryer level and washer spin speed. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
What GE Dryer Codes Mean
| Code | What it means |
|---|---|
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Dryer shuts off a few minutes into the cycle
- Cycles take two or three runs to finish
- Drum will not turn even though you hear a hum
Inside a Dryer Repair Visit
Care GE Recommends for Its Dryers
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
Brand guides: GE Dryer Not Heating: What to Check.
GE Dryer Repair Cost Ranges
A GE dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Igniter replacement (gas dryer): $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Timer replacement: $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Control board (part only): $90–$280 Source: Angi - How Much Does Dryer Repair Cost?
- Technician service / diagnostic fee, dryer: $50–$80 per visit Source: Fixr - How much does it cost to repair a dryer?
Replacement makes more sense once a dryer is about 10 years old or past half its expected lifespan. Source: Fixr - How much does it cost to repair a dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Getting Ready for the Repair
- The brand, model and serial number from the label inside the door or on the back panel
- Any error code on the display
- What happens when you press Start (no response, hum, runs with no heat, stops early)
Around Asheville
Most dryer calls in Asheville come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
North Carolina has no license specific to appliance repair; work on gas appliances, fuel piping and heating equipment is regulated by the State Board of Examiners of Plumbing, Heating, and Fire Sprinkler Contractors, with an exemption for minor repairs that don't change fuel type, venting or piping. Source: N.C. Gen. Stat. § 87-21 (NC General Assembly)
Gas and fuel piping installation requires a plumbing or heating license, or a restricted fuel piping license, issued by the State Board of Examiners of Plumbing, Heating, and Fire Sprinkler Contractors. Source: N.C. Gen. Stat. § 87-21 (NC General Assembly)
Questions to Ask a Asheville Technician
- If a part has to be ordered, how soon can you come back to finish?
- What guarantee do you give on parts and labor?
- Can you look at the washer on the same visit if it is acting up too?
GE Dryer Repair FAQs: Asheville, NC
Why does my GE dryer show an error code?
Do you work for GE?
Why do my clothes come out damp?
Other Dryer Repair in Asheville
More GE Dryer Repair Pages Nearby
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.