If your GE dryer has stopped heating, stopped tumbling or started throwing an error code, the technician you call should know the model line. Below are independent repair companies serving James City, with those that mention GE first, then the nearest dryer repair companies.
Independent listings only: Washer and Dryer Repair is not affiliated with or endorsed by GE. If your dryer is still under manufacturer coverage, contact GE directly.
Who Works on GE Dryers Near James City
We found 27 appliance repair companies within 60 miles of James City. The rest are spread across Jacksonville (5), Washington (4), and New Bern (3). The farthest listed company is about 60 miles out. The closest is ROWE APPLIANCE, about 3.9 miles away. No company within 90 miles of James City mentions GE by name, so these are the nearest appliance repair companies. Most work on several brands, so ask about yours. The 20 rated companies in range average 4.5 stars. James City is a smaller market, so expect a longer drive and ask whether a trip charge applies.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| With 4.5+ stars and at least 10 reviews | 12 |
|---|---|
| Listing Saturday hours | 13 |
| Distance to the three closest (mi) | 3.9, 4.4, 6.1 |
| Appliance repair companies in range (60 mi) | 27 |
| Show laundry appliance work | 7 |
| Mention GE | 0 |
The leading options for James City are Cavalry Appliance Service (4.4 miles away, based in New Bern, 4.9 stars from 535 reviews); Sears Appliance Repair (26.0 miles away, based in Morehead City, 4.5 stars from 178 reviews, lists Saturday hours); Sears Appliance Repair (28.8 miles away, based in Jacksonville, 4.6 stars from 234 reviews, lists Saturday hours); Aaron’s Appliance Repair (JACKSONVILLE) (26.9 miles away, based in Jacksonville, 4.0 stars from 64 reviews, lists Saturday hours).
Know Your GE Dryer
How GE Dryers Are Built
GE allows only rigid or flexible metal vent duct and says plastic flexible duct is not acceptable because it collapses, cuts airflow and can collect water. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
What GE Says to Check First
- Dryer will not run or start. GE's first check is that the dryer plug is pushed fully into the wall outlet. Source: GE Appliances - Dryer - Will Not Run or Start
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
What GE Dryer Codes Mean
| Code | What it means |
|---|---|
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Clothes still damp after a full cycle
- Cycles take two or three runs to finish
- Dryer shuts off a few minutes into the cycle
What a Dryer Repair Technician Checks
Keeping a GE Dryer Running
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
Brand guides: GE Dryer Not Heating: What to Check.
What GE Dryer Repairs Cost
A GE dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Drive motor replacement: $250–$450 Source: Fixr - How much does it cost to repair a dryer?
- Control board (part only): $90–$280 Source: Angi - How Much Does Dryer Repair Cost?
- Heating element replacement: $150–$350 Source: Fixr - How much does it cost to repair a dryer?
- Igniter replacement (gas dryer): $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Service call fee (may be waived if the technician does the repair): $50–$80 per visit Source: Angi - How Much Does It Cost to Repair a Dryer?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Getting Ready for the Repair
- Whether the dryer is gas or electric
- How long the vent run is and where it exits the house
- What happens when you press Start (no response, hum, runs with no heat, stops early)
Around James City
Most dryer calls in James City come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
North Carolina has no license specific to appliance repair; work on gas appliances, fuel piping and heating equipment is regulated by the State Board of Examiners of Plumbing, Heating, and Fire Sprinkler Contractors, with an exemption for minor repairs that don't change fuel type, venting or piping. Source: N.C. Gen. Stat. § 87-21 (NC General Assembly)
In North Carolina, you can check a license with the NC Plumbing, Heating and Fire Sprinkler Board public license search or report a problem to the North Carolina Department of Justice, Consumer Protection Division.
Questions to Ask a James City Technician
- What guarantee do you give on parts and labor?
- Do you work on gas dryers, and who handles anything involving the gas line?
- Is your company licensed where my state requires it, and insured?
GE Dryer Repair FAQs: James City, NC
Is my GE dryer worth repairing?
What should I do about a GE error code?
How do I find a technician who knows GE dryers?
What makes a dryer stop heating?
Related Repair Pages for James City
GE Dryer Repair in Nearby Cities
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.