Most GE dryer repairs in Miami involve the same few systems: heat, airflow, the drum drive and the controls. Below are independent repair companies serving Miami, with those that mention GE first, then the nearest dryer repair companies.
Independent listings only: Washer and Dryer Repair is not affiliated with or endorsed by GE. If your dryer is still under manufacturer coverage, contact GE directly.
GE Dryer Repair Near Miami
We found 30 appliance repair companies within 60 miles of Miami. Other nearby bases include Joplin (8), Bartlesville (3), and Pittsburg (2). Distances run up to about 60 miles. None of the repair companies near Miami name GE in their listings, so we show the closest appliance repair companies. Ask each one about your model before booking. The closest is Big M Appliance Repair, about 11.6 miles away. Rated companies nearby average 4.0 stars across 29 businesses. Because the nearest shops are farther out, ask each company whether Miami is inside its regular service area.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| Listing Saturday hours | 13 |
|---|---|
| Rated 4.5 stars or higher (10+ reviews) | 12 |
| List dryer or washer & dryer work | 11 |
| Distance to the three closest (mi) | 11.6, 21.5, 22.5 |
| Mention GE | 0 |
| Companies within 60 miles | 30 |
Closest matches for Miami: Mr. Appliance of Joplin (24.2 miles away, based in Joplin, 4.9 stars from 426 reviews); Mr. Appliance of Springdale and Rogers (52.1 miles away, based in Bentonville, 4.9 stars from 782 reviews); Bowers Service Co (36.0 miles away, based in Carthage, 4.8 stars from 156 reviews); Big M Appliance Repair (11.6 miles away, based in Baxter Springs, 4.6 stars from 54 reviews, lists Saturday hours).
GE Dryer Lines and Features
What a GE Dryer Technician Deals With
GE allows only rigid or flexible metal vent duct and says plastic flexible duct is not acceptable because it collapses, cuts airflow and can collect water. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
What GE Says to Check First
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
- Dryer takes too long to dry. GE points first to venting (metal duct, no kinks, clear wall cap) and a clean lint filter, then to load size, dryer level and washer spin speed. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Reading a GE Dryer Error Code
| Code | What it means |
|---|---|
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Squealing, thumping or grinding while it runs
- Cycles take two or three runs to finish
- Outside of the cabinet gets unusually hot
What a Dryer Repair Technician Checks
Keeping a GE Dryer Running
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Brand guides: GE Dryer Not Heating: What to Check.
What GE Dryer Repairs Cost
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Thermal fuse repair: $80–$130 Source: Angi - How Much Does It Cost to Repair a Dryer?
- Door switch replacement: $50–$150 Source: Fixr - How much does it cost to repair a dryer?
- Drum bearing replacement: $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Dryer not heating (repair by symptom): $80–$420 Source: Angi - How Much Does Dryer Repair Cost?
- Service call fee (may be waived if the technician does the repair): $50–$80 per visit Source: Angi - How Much Does It Cost to Repair a Dryer?
A dryer that keeps needing repairs despite regular maintenance is usually cheaper to replace. Source: Angi - How Much Does Dryer Repair Cost?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Getting Ready for the Repair
- Whether the dryer is gas or electric
- How long the vent run is and where it exits the house
- What happens when you press Start (no response, hum, runs with no heat, stops early)
Dryer Notes for Miami, OK
Most dryer calls in Miami come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Oklahoma has no general appliance repair license; mechanical licensing through the Construction Industries Board excludes minor repairs the manufacturer allows an owner or agent to make, but that exclusion does not reach gas piping, gas controls, appliance venting or opening a sealed refrigeration system. Source: OAC 158:50 Mechanical Industry Rules (Oklahoma Construction Industries Board)
Natural gas piping work requires a Natural Gas Piping mechanical license or a plumbing license issued by the Oklahoma Construction Industries Board. Source: OAC 158:50 Mechanical Industry Rules (Oklahoma Construction Industries Board)
Before You Book in Miami
- Will you check the vent and lint path as part of the visit?
- Can you look at the washer on the same visit if it is acting up too?
- What guarantee do you give on parts and labor?
GE Dryer Repair FAQs: Miami, OK
Is my GE dryer worth repairing?
Is this GE customer service?
Why does my dryer take so long to dry?
Why is my dryer running but not heating?
Related Repair Pages for Miami
GE Dryer Repair in Nearby Cities
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.