Most GE dryer repairs in Tulsa involve the same few systems: heat, airflow, the drum drive and the controls. The Tulsa list starts with companies that name GE, followed by other appliance repair companies that list dryer work.
Washer and Dryer Repair is independent and not affiliated with GE. Listed companies are independent technicians who repair GE dryers and other brands.
GE Dryer Repair Near Tulsa
We found 33 appliance repair companies within 30 miles of Tulsa. 19 list an address in Tulsa, and the rest are spread across Owasso (4), Broken Arrow (3), and Sand Springs (2). Distances run up to about 18 miles. Appliance Solutions is the nearest, roughly 1.7 miles from Tulsa. No company within 90 miles of Tulsa mentions GE by name, so these are the nearest appliance repair companies. Most work on several brands, so ask about yours. Across 30 rated companies, the average public rating is 4.4 stars.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| Mention GE | 0 |
|---|---|
| Three nearest companies, miles away | 1.7, 1.9, 2.0 |
| Listing Saturday hours | 17 |
| Appliance repair companies in range (30 mi) | 33 |
| Rated 4.5 stars or higher (10+ reviews) | 13 |
| List dryer or washer & dryer work | 12 |
First up for Tulsa: Mr. Appliance of Metro Tulsa (2.0 miles away, 4.8 stars from 1,114 reviews); CJ Appliance Repair Tulsa (6.0 miles away, 4.9 stars from 666 reviews); Appliance Solutions (1.7 miles away, 4.8 stars from 1,157 reviews, lists Saturday hours); Sears Appliance Repair (4.6 miles away, 4.6 stars from 332 reviews, lists Saturday hours).
Know Your GE Dryer
What a GE Dryer Technician Deals With
The GE Profile UltraFast Combo uses a two-stage filter system (a mesh lint filter plus a second mesh or foam filter) located between the display and the dispenser drawers. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
Some GE dryers have an airflow sensor that shows a Check Vent alert when exhaust airflow drops, which usually means the vent is blocked. Source: GE Appliances - Dryer - Check Vent Sensor Alert
Common GE Dryer Problems
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
What GE Dryer Codes Mean
| Code | What it means |
|---|---|
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
When to Call for GE Dryer Repair
- Cycles take two or three runs to finish
- Burning or hot smell during a cycle
- Squealing, thumping or grinding while it runs
Inside a Dryer Repair Visit
Owner Care for GE Dryers
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Brand guides: GE Dryer Not Heating: What to Check.
What GE Dryer Repairs Cost
A GE dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Drive motor replacement: $250–$450 Source: Fixr - How much does it cost to repair a dryer?
- Control board (part only): $90–$280 Source: Angi - How Much Does Dryer Repair Cost?
- Drum roller replacement: $100–$150 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair (most homeowners): $100–$430 Source: Angi - How Much Does Dryer Repair Cost?
- Technician labor: $50–$100 per hour Source: Angi - How Much Does Dryer Repair Cost?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Getting Ready for the Repair
- Whether the dryer is gas or electric
- The brand, model and serial number from the label inside the door or on the back panel
- How long the vent run is and where it exits the house
What Tulsa Owners Should Know
Most dryer calls in Tulsa come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Oklahoma has no general appliance repair license; mechanical licensing through the Construction Industries Board excludes minor repairs the manufacturer allows an owner or agent to make, but that exclusion does not reach gas piping, gas controls, appliance venting or opening a sealed refrigeration system. Source: OAC 158:50 Mechanical Industry Rules (Oklahoma Construction Industries Board)
Natural gas piping work requires a Natural Gas Piping mechanical license or a plumbing license issued by the Oklahoma Construction Industries Board. Source: OAC 158:50 Mechanical Industry Rules (Oklahoma Construction Industries Board)
How to Choose a Dryer Technician Near Tulsa
- Can you look at the washer on the same visit if it is acting up too?
- How often do you repair GE dryers, and do you carry common parts on the truck?
- Will you check the vent and lint path as part of the visit?
GE Dryer Repair FAQs: Tulsa, OK
Why do my clothes come out damp?
How do I find a technician who knows GE dryers?
Should I repair or replace my GE dryer?
Other Dryer Repair in Tulsa
GE Dryer Repair Near Tulsa
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.