GE owners in Fairview usually want two things from a repair company: experience with the brand and quick access to parts. The Fairview list starts with companies that name GE, followed by other appliance repair companies that list dryer work.
Washer and Dryer Repair is independent and not affiliated with GE. Listed companies are independent technicians who repair GE dryers and other brands.
Independent GE Dryer Technicians, Fairview TN
We found 40 appliance repair companies within 30 miles of Fairview. The rest are spread across Nashville (25), Franklin (5), and Brentwood (3). Distances run up to about 26 miles. The closest is All Better Appliance LLC, about 4.7 miles away. None of the repair companies near Fairview name GE in their listings, so we show the closest appliance repair companies. Ask each one about your model before booking. The 34 rated companies in range average 4.4 stars.
Companies are shown by relevance and distance from Fairview. A mention does not mean manufacturer certification, so ask each company about its experience with your dryer.
| With 4.5+ stars and at least 10 reviews | 17 |
|---|---|
| Mention GE | 0 |
| Open on Saturdays (per listing) | 28 |
| List dryer or washer & dryer work | 14 |
| Distance to the three closest (mi) | 4.7, 10.9, 13.4 |
| Appliance repair companies in range (30 mi) | 49 |
First up for Fairview: All Better Appliance LLC (4.7 miles away, based in Burns, 4.8 stars from 95 reviews); Mills Appliances , formerly Soll's Appliance (16.2 miles away, based in Dickson, 4.8 stars from 152 reviews); New Life Appliance (18.5 miles away, based in Spring Hill, 4.9 stars from 106 reviews); Fix-It-Right Appliance Repair (18.6 miles away, based in Brentwood, 4.6 stars from 188 reviews, lists Saturday hours).
Know Your GE Dryer
How GE Dryers Are Built
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
What GE Says to Check First
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
GE Dryer Error Codes
| Code | What it means |
|---|---|
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Cycles take two or three runs to finish
- Clothes still damp after a full cycle
- Drum turns but the air stays cool
What a Dryer Repair Technician Checks
Care GE Recommends for Its Dryers
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
Brand guides: GE Dryer Not Heating: What to Check.
Budgeting for a GE Dryer Repair
A GE dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Drum bearing replacement: $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Thermostat replacement: $100–$260 Source: Fixr - How much does it cost to repair a dryer?
- Heating element replacement: $150–$350 Source: Fixr - How much does it cost to repair a dryer?
- Dryer not heating (repair by symptom): $80–$420 Source: Angi - How Much Does Dryer Repair Cost?
- Service call fee (may be waived if the technician does the repair): $50–$80 per visit Source: Angi - How Much Does It Cost to Repair a Dryer?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Getting Ready for the Repair
- Whether the dryer is gas or electric
- Any error code on the display
- How long the vent run is and where it exits the house
Dryer Notes for Fairview, TN
Most dryer calls in Fairview come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Tennessee's Board for Licensing Contractors does not list an appliance repair license among the licenses it issues (general contractor, home improvement, limited licensed electrician and limited licensed plumber). Source: TN Board for Licensing Contractors
Gas piping and gas appliance installation permits are handled by local governments, some of which require their own gas fitter license; for example, Chattanooga requires a city Master Gas Fitter License to pull a gas permit. Source: City of Chattanooga: Gas Permit
How to Choose a Dryer Technician Near Fairview
- Is your company licensed where my state requires it, and insured?
- Do you work on gas dryers, and who handles anything involving the gas line?
- Can you give a written estimate before ordering parts?
GE Dryer Repair FAQs: Fairview, TN
Is this GE customer service?
Which Fairview technicians work on GE?
What should I do about a GE error code?
Related Repair Pages for Fairview
GE Dryer Repair Near Fairview
Clean the lint screen, check the vent hood outside and note the model number before calling. It rules out the simple causes and speeds up a GE repair.