Most GE dryer repairs in Kingsport involve the same few systems: heat, airflow, the drum drive and the controls. We flag companies whose listing or website mentions GE and fill in with nearby dryer repair companies so you always have options.
This is an independent directory. We are not affiliated with GE, and the technicians listed are independent repair companies, not the manufacturer.
GE Dryer Repair Near Kingsport
We found 19 appliance repair companies within 30 miles of Kingsport. 3 list an address in Kingsport, and other nearby bases include Johnson City (4), Bristol (3), and Greeneville (3). The farthest listed company is about 29 miles out. 1 lists GE specifically. The closest is Milhorn Appliance, about 1.9 miles away. The 19 rated companies in range average 4.4 stars.
Companies are shown by relevance and distance from Kingsport. A mention does not mean manufacturer certification, so ask each company about its experience with your dryer.
| Show laundry appliance work | 5 |
|---|---|
| Repair companies inside 30 miles | 19 |
| Rated 4.5 stars or higher (10+ reviews) | 8 |
| Mention GE | 1 |
| Listing Saturday hours | 7 |
| Distance to the three closest (mi) | 1.9, 2.3, 2.3 |
At the top of the Kingsport list: Sears Appliance Repair (2.3 miles away, 4.5 stars from 174 reviews, lists Saturday hours); Mr. Appliance of the Tri-Cities (8.3 miles away, based in Gray, 4.5 stars from 1,004 reviews); Sears Appliance Repair (15.7 miles away, based in Johnson City, 4.4 stars from 277 reviews, lists Saturday hours); Sears Appliance Repair (27.7 miles away, based in Greeneville, 4.5 stars from 119 reviews, lists Saturday hours).
Know Your GE Dryer
How GE Dryers Are Built
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
The GE Profile UltraFast Combo uses a two-stage filter system (a mesh lint filter plus a second mesh or foam filter) located between the display and the dispenser drawers. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
Common GE Dryer Problems
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
- Gas dryer runs but does not heat. GE says to confirm a real drying cycle and temperature are selected, keep the front of the dryer unblocked, check the dedicated 120V outlet, and on new installs make sure the gas line is turned on. Source: GE Appliances - Gas Dryer - Runs But Does Not Heat
What GE Dryer Codes Mean
| Code | What it means |
|---|---|
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Drum turns but the air stays cool
- Dryer shuts off a few minutes into the cycle
- Dryer will not start when you press Start
How a Dryer Service Call Usually Goes in Kingsport
Keeping a GE Dryer Running
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Brand guides: GE Dryer Not Heating: What to Check.
GE Dryer Repair Cost Ranges
A GE dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Gas valve coil replacement (gas dryer): $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Drum belt replacement: $150–$250 Source: Fixr - How much does it cost to repair a dryer?
- Door switch replacement: $50–$150 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair (most homeowners): $100–$430 Source: Angi - How Much Does Dryer Repair Cost?
- Technician labor: $50–$100 per hour Source: Angi - How Much Does Dryer Repair Cost?
A dryer that keeps needing repairs despite regular maintenance is usually cheaper to replace. Source: Angi - How Much Does Dryer Repair Cost?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Before the Technician Arrives
- How long the vent run is and where it exits the house
- The brand, model and serial number from the label inside the door or on the back panel
- Whether the dryer is gas or electric
Local Notes for Kingsport
Most dryer calls in Kingsport come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Tennessee's Board for Licensing Contractors does not list an appliance repair license among the licenses it issues (general contractor, home improvement, limited licensed electrician and limited licensed plumber). Source: TN Board for Licensing Contractors
In Tennessee, you can check a license with the Tennessee Department of Commerce and Insurance: Verify a License or report a problem to the Tennessee Division of Consumer Affairs (Office of the Attorney General).
Questions to Ask a Kingsport Technician
- Will you check the vent and lint path as part of the visit?
- Can you give a written estimate before ordering parts?
- If a part has to be ordered, how soon can you come back to finish?
GE Dryer Repair FAQs: Kingsport, TN
Is my GE dryer worth repairing?
How do I find a technician who knows GE dryers?
Why do my clothes come out damp?
Other Dryer Repair in Kingsport
GE Dryer Repair in Nearby Cities
Clean the lint screen, check the vent hood outside and note the model number before calling. It rules out the simple causes and speeds up a GE repair.