Most GE dryer repairs in Missouri City involve the same few systems: heat, airflow, the drum drive and the controls. Below are independent repair companies serving Missouri City, with those that mention GE first, then the nearest dryer repair companies.
Independent listings only: Washer and Dryer Repair is not affiliated with or endorsed by GE. If your dryer is still under manufacturer coverage, contact GE directly.
Independent GE Dryer Technicians, Missouri City TX
Within 30 miles of Missouri City there are 40 appliance repair companies in our data. 5 list an address in Missouri City, and the rest are spread across Sugar Land (18), Houston (10), and Stafford (2). Distances run up to about 10 miles. No company within 30 miles of Missouri City names GE in its listing, so the list adds matches from farther out and the closest appliance repair companies. A+ Appliance Repair Missouri City is the nearest, roughly 1.6 miles from Missouri City. Across 33 rated companies, the average public rating is 4.5 stars.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| Mention GE | 0 |
|---|---|
| Three nearest companies, miles away | 1.6, 1.8, 2.1 |
| Companies within 30 miles | 60 |
| With 4.5+ stars and at least 10 reviews | 21 |
| List dryer or washer & dryer work | 18 |
| Listing Saturday hours | 48 |
First up for Missouri City: Sears Appliance Repair (21.0 miles away, based in Alvin, 4.4 stars from 84 reviews, lists Saturday hours); Sears Appliance Repair (57.5 miles away, based in Liberty, 4.7 stars from 126 reviews, lists Saturday hours); Sears Appliance Repair (85.5 miles away, based in La Grange, 4.7 stars from 61 reviews, lists Saturday hours); ️ Kenmore Appliance Repair Pros in Stafford, TX (5.3 miles away, based in Stafford, 4.9 stars from 12 reviews, lists Saturday hours).
GE Dryer Lines and Features
How GE Dryers Are Built
GE allows only rigid or flexible metal vent duct and says plastic flexible duct is not acceptable because it collapses, cuts airflow and can collect water. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
The GE Profile UltraFast Combo uses a two-stage filter system (a mesh lint filter plus a second mesh or foam filter) located between the display and the dispenser drawers. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
GE Dryer Symptoms and First Checks
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
GE Dryer Error Codes
| Code | What it means |
|---|---|
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
When to Call for GE Dryer Repair
- Drum turns but the air stays cool
- Dryer shuts off a few minutes into the cycle
- Drum will not turn even though you hear a hum
What a Dryer Repair Technician Checks
Keeping a GE Dryer Running
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
Brand guides: GE Dryer Not Heating: What to Check.
Budgeting for a GE Dryer Repair
A GE dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Timer replacement: $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Thermostat replacement: $100–$260 Source: Fixr - How much does it cost to repair a dryer?
- Heating element replacement: $150–$350 Source: Fixr - How much does it cost to repair a dryer?
- Dryer not heating (repair by symptom): $80–$420 Source: Angi - How Much Does Dryer Repair Cost?
- Technician service / diagnostic fee, dryer: $50–$80 per visit Source: Fixr - How much does it cost to repair a dryer?
Replacement makes more sense once a dryer is about 10 years old or past half its expected lifespan. Source: Fixr - How much does it cost to repair a dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Before the Technician Arrives
- What happens when you press Start (no response, hum, runs with no heat, stops early)
- The brand, model and serial number from the label inside the door or on the back panel
- How long the vent run is and where it exits the house
Around Missouri City
Most dryer calls in Missouri City come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Texas has no separate appliance repair license; under the Plumbing License Law, appliance dealers and their employees may install and service appliances (other than water heaters) without a plumbing license when hooking up to existing openings with a code-approved appliance connector, while other gas or water piping work generally requires a plumbing license. Source: Plumbing License Law, Tex. Occ. Code ch. 1301, §1301.053 (Texas State Board of Plumbing Examiners)
Gas piping counts as plumbing in Texas and requires a plumbing license, with an exemption for LP gas installers who hold a separate state LP gas license. Source: Plumbing License Law, Tex. Occ. Code ch. 1301, §§1301.002, 1301.055 (Texas State Board of Plumbing Examiners)
How to Choose a Dryer Technician Near Missouri City
- What guarantee do you give on parts and labor?
- Can you look at the washer on the same visit if it is acting up too?
- Is your company licensed where my state requires it, and insured?
GE Dryer Repair FAQs: Missouri City, TX
Is this GE customer service?
What should I do about a GE error code?
How do I find a technician who knows GE dryers?
Other Dryer Repair in Missouri City
GE Dryer Repair in Nearby Cities
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.