If your GE dryer has stopped heating, stopped tumbling or started throwing an error code, the technician you call should know the model line. Below are independent repair companies serving Washington, with those that mention GE first, then the nearest dryer repair companies.
Washer and Dryer Repair is independent and not affiliated with GE. Listed companies are independent technicians who repair GE dryers and other brands.
Who Works on GE Dryers Near Washington
Our data shows 9 appliance repair companies inside a 60-mile radius of Washington. 1 of them are based in Washington itself, and the rest are spread across St. George (4), Cedar City (2), and Hurricane (1). The farthest listed company is about 47 miles out. The closest is JJ Service and Repair, about 0.7 miles away. No company within 90 miles of Washington mentions GE by name, so these are the nearest appliance repair companies. Most work on several brands, so ask about yours. Across 8 rated companies, the average public rating is 4.4 stars. Washington is a smaller market, so expect a longer drive and ask whether a trip charge applies.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| Mention GE | 0 |
|---|---|
| Open on Saturdays (per listing) | 4 |
| Three nearest companies, miles away | 0.7, 3.3, 3.8 |
| Rated 4.5 stars or higher (10+ reviews) | 3 |
| Show laundry appliance work | 2 |
| Companies within 60 miles | 9 |
The leading options for Washington are Mr. Appliance of St. George (6.0 miles away, based in St. George, 4.8 stars from 1,430 reviews, lists Saturday hours); Sears Appliance Repair (3.3 miles away, based in St. George, 4.1 stars from 249 reviews, lists Saturday hours); Appliance Repair Center (11.1 miles away, based in Hurricane, 4.9 stars from 74 reviews, lists Saturday hours); JJ Service and Repair (0.7 miles away, 4.9 stars from 107 reviews).
GE Dryer Features Technicians Work On
How GE Dryers Are Built
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
GE Dryer Symptoms and First Checks
- Gas dryer runs but does not heat. GE says to confirm a real drying cycle and temperature are selected, keep the front of the dryer unblocked, check the dedicated 120V outlet, and on new installs make sure the gas line is turned on. Source: GE Appliances - Gas Dryer - Runs But Does Not Heat
- Check Vent alert. GE says to unplug the dryer, disconnect and vacuum the duct, and make sure the outside hood damper moves freely. Source: GE Appliances - Dryer - Check Vent Sensor Alert
GE Dryer Error Codes
| Code | What it means |
|---|---|
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
When to Call for GE Dryer Repair
- Cycles take two or three runs to finish
- Dryer shuts off a few minutes into the cycle
- Outside of the cabinet gets unusually hot
What Gets Fixed on a Washington Dryer Call
Care GE Recommends for Its Dryers
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Brand guides: GE Dryer Not Heating: What to Check.
What GE Dryer Repairs Cost
A GE dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Thermal fuse repair: $80–$130 Source: Angi - How Much Does It Cost to Repair a Dryer?
- Gas valve coil replacement (gas dryer): $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Thermostat replacement: $100–$260 Source: Fixr - How much does it cost to repair a dryer?
- Timer replacement: $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair (most homeowners): $100–$430 Source: Angi - How Much Does Dryer Repair Cost?
- Appliance technician diagnosis, washer (usually waived if hired for the repair): $50–$100 per visit Source: Fixr - How much does it cost to repair a washing machine?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Before the Technician Arrives
- The brand, model and serial number from the label inside the door or on the back panel
- Any error code on the display
- What happens when you press Start (no response, hum, runs with no heat, stops early)
Local Notes for Washington
Most dryer calls in Washington come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Utah has no contractor classification for appliance repair, but under the Construction Trades Licensing Act anyone who installs, repairs or replaces a residential or commercial gas appliance must hold natural gas technician certification, even on jobs otherwise too small to need a contractor license. Source: Utah Legislature H.B. 49 (2004), Natural Gas Technician Certification, amending Utah Code 58-55-305 and 58-55-308
Gas appliance and combustion system work, starting at the outlet of the gas meter, falls under DOPL's construction trades licensing, and the qualifier for an HVAC contractor license must be a Certified Natural Gas Technician. Source: DOPL Contractor Classifications
How to Choose a Dryer Technician Near Washington
- What guarantee do you give on parts and labor?
- How often do you repair GE dryers, and do you carry common parts on the truck?
- Can you give a written estimate before ordering parts?
GE Dryer Repair FAQs: Washington, UT
What makes a dryer stop heating?
Do you work for GE?
Which Washington technicians work on GE?
Why does my dryer take so long to dry?
Related Repair Pages for Washington
GE Dryer Repair Near Washington
Clean the lint screen, check the vent hood outside and note the model number before calling. It rules out the simple causes and speeds up a GE repair.