If your GE dryer has stopped heating, stopped tumbling or started throwing an error code, the technician you call should know the model line. The Santa Clara list starts with companies that name GE, followed by other appliance repair companies that list dryer work.
This is an independent directory. We are not affiliated with GE, and the technicians listed are independent repair companies, not the manufacturer.
Independent GE Dryer Technicians, Santa Clara UT
Our data shows 9 appliance repair companies inside a 60-mile radius of Santa Clara. The rest are spread across St. George (4), Cedar City (2), and Washington (1). The farthest listed company is about 52 miles out. Nearest on the list: Mr. Appliance of St. George, around 3.5 miles out. No company within 90 miles of Santa Clara mentions GE by name, so these are the nearest appliance repair companies. Most work on several brands, so ask about yours. The 8 rated companies in range average 4.4 stars. Santa Clara is a smaller market, so expect a longer drive and ask whether a trip charge applies.
Listings come from public business data. A brand or service mention means the company names it in its listing or website; it is not a certification. Verify experience, licensing and insurance before hiring.
| Open on Saturdays (per listing) | 4 |
|---|---|
| With 4.5+ stars and at least 10 reviews | 3 |
| Appliance repair companies in range (60 mi) | 9 |
| Mention GE | 0 |
| Three nearest companies, miles away | 3.5, 5.4, 5.6 |
| List dryer or washer & dryer work | 2 |
At the top of the Santa Clara list: Mr. Appliance of St. George (3.5 miles away, based in St. George, 4.8 stars from 1,430 reviews, lists Saturday hours); Sears Appliance Repair (6.2 miles away, based in St. George, 4.1 stars from 249 reviews, lists Saturday hours); St George Appliance Repair (5.6 miles away, based in St. George, 4.0 stars from 95 reviews, lists Saturday hours); Appliance Repair Center (20.1 miles away, based in Hurricane, 4.9 stars from 74 reviews, lists Saturday hours).
GE Dryer Features Technicians Work On
What Makes GE Dryer Repairs Different
Some GE dryers have an airflow sensor that shows a Check Vent alert when exhaust airflow drops, which usually means the vent is blocked. Source: GE Appliances - Dryer - Check Vent Sensor Alert
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
What GE Says to Check First
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
- Dryer takes too long to dry. GE points first to venting (metal duct, no kinks, clear wall cap) and a clean lint filter, then to load size, dryer level and washer spin speed. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
GE Dryer Error Codes
| Code | What it means |
|---|---|
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Clothes still damp after a full cycle
- Outside of the cabinet gets unusually hot
- Cycles take two or three runs to finish
Inside a Dryer Repair Visit
Care GE Recommends for Its Dryers
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Brand guides: GE Dryer Not Heating: What to Check.
GE Dryer Repair Cost Ranges
A GE dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Control board (part only): $90–$280 Source: Angi - How Much Does Dryer Repair Cost?
- Thermostat replacement: $100–$260 Source: Fixr - How much does it cost to repair a dryer?
- Thermal fuse repair: $80–$130 Source: Angi - How Much Does It Cost to Repair a Dryer?
- Heating element replacement: $150–$350 Source: Fixr - How much does it cost to repair a dryer?
- Dryer not heating (repair by symptom): $80–$420 Source: Angi - How Much Does Dryer Repair Cost?
- Service call fee (may be waived if the technician does the repair): $50–$80 per visit Source: Angi - How Much Does It Cost to Repair a Dryer?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Before the Technician Arrives
- How long the vent run is and where it exits the house
- Any error code on the display
- What happens when you press Start (no response, hum, runs with no heat, stops early)
Dryer Notes for Santa Clara, UT
Most dryer calls in Santa Clara come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Utah has no contractor classification for appliance repair, but under the Construction Trades Licensing Act anyone who installs, repairs or replaces a residential or commercial gas appliance must hold natural gas technician certification, even on jobs otherwise too small to need a contractor license. Source: Utah Legislature H.B. 49 (2004), Natural Gas Technician Certification, amending Utah Code 58-55-305 and 58-55-308
In Utah, you can check a license with the Utah Licensee Lookup and Verification (Verify a License) or report a problem to the Utah Department of Commerce, Division of Consumer Protection.
Hiring a Dryer Repair Company in Santa Clara
- Is your company licensed where my state requires it, and insured?
- If a part has to be ordered, how soon can you come back to finish?
- What is the service call or diagnostic fee, and is it applied to the repair?
GE Dryer Repair FAQs: Santa Clara, UT
Why do my clothes come out damp?
Which Santa Clara technicians work on GE?
What makes a dryer stop heating?
Related Repair Pages for Santa Clara
GE Dryer Repair in Nearby Cities
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.