Most GE dryer repairs in Martinsville involve the same few systems: heat, airflow, the drum drive and the controls. We flag companies whose listing or website mentions GE and fill in with nearby dryer repair companies so you always have options.
Independent listings only: Washer and Dryer Repair is not affiliated with or endorsed by GE. If your dryer is still under manufacturer coverage, contact GE directly.
GE Dryer Repair Near Martinsville
Our data shows 13 appliance repair companies inside a 30-mile radius of Martinsville. Other nearby bases include Eden (3), Bassett (2), and Danville (2). Randall's Appliances & Plumbing is the nearest, roughly 10.5 miles from Martinsville. No company within 30 miles of Martinsville names GE in its listing, so the list adds matches from farther out and the closest appliance repair companies. The 12 rated companies in range average 3.7 stars.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| Three nearest companies, miles away | 10.5, 11.7, 12.3 |
|---|---|
| Appliance repair companies in range (30 mi) | 13 |
| Listing Saturday hours | 5 |
| Mention GE | 0 |
| Show laundry appliance work | 0 |
| Rated 4.5 stars or higher (10+ reviews) | 3 |
The leading options for Martinsville are Sears Appliance Repair (77.0 miles away, based in Covington, 4.4 stars from 42 reviews, lists Saturday hours); GE Appliance Services (40.9 miles away, based in Roanoke, 1.0 stars from 6 reviews, lists Saturday hours); Randall's Appliances & Plumbing (10.5 miles away, based in Bassett, 4.4 stars from 15 reviews); Alan's Service Center (13.2 miles away, based in Eden, 2.8 stars from 17 reviews, lists Saturday hours).
Know Your GE Dryer
How GE Dryers Are Built
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Common GE Dryer Problems
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
What GE Dryer Codes Mean
| Code | What it means |
|---|---|
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
When to Call for GE Dryer Repair
- Drum turns but the air stays cool
- Squealing, thumping or grinding while it runs
- Dryer will not start when you press Start
Inside a Dryer Repair Visit
Owner Care for GE Dryers
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
Brand guides: GE Dryer Not Heating: What to Check.
What GE Dryer Repairs Cost
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Heating element replacement: $150–$350 Source: Fixr - How much does it cost to repair a dryer?
- Drive motor replacement: $250–$450 Source: Fixr - How much does it cost to repair a dryer?
- Drum bearing replacement: $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Dryer not heating (repair by symptom): $80–$420 Source: Angi - How Much Does Dryer Repair Cost?
- Appliance technician diagnosis, washer (usually waived if hired for the repair): $50–$100 per visit Source: Fixr - How much does it cost to repair a washing machine?
A dryer that keeps needing repairs despite regular maintenance is usually cheaper to replace. Source: Angi - How Much Does Dryer Repair Cost?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Before the Technician Arrives
- Any error code on the display
- The brand, model and serial number from the label inside the door or on the back panel
- How long the vent run is and where it exits the house
What Martinsville Owners Should Know
Most dryer calls in Martinsville come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Virginia's Board for Contractors has no appliance repair license classification, but its gas fitting contracting specialty covers installing, repairing or removing gas piping and appliances attached to real property. Source: 18VAC50-22-30, Definitions of specialty services
The Board for Contractors licenses gas fitting contractors and individual gas fitter, natural gas fitter and liquefied petroleum gas fitter tradesmen. Source: 18VAC50-30-10, Definitions (Individual License and Certification Regulations)
Before You Book in Martinsville
- Do you work on gas dryers, and who handles anything involving the gas line?
- If a part has to be ordered, how soon can you come back to finish?
- What is the service call or diagnostic fee, and is it applied to the repair?
GE Dryer Repair FAQs: Martinsville, VA
What should I do about a GE error code?
Is my GE dryer worth repairing?
Why does my dryer take so long to dry?
Do you work for GE?
More Laundry Repair in Martinsville, VA
More GE Dryer Repair Pages Nearby
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.