If your GE dryer has stopped heating, stopped tumbling or started throwing an error code, the technician you call should know the model line. The Fairwood list starts with companies that name GE, followed by other appliance repair companies that list dryer work.
This is an independent directory. We are not affiliated with GE, and the technicians listed are independent repair companies, not the manufacturer.
GE Dryer Repair Near Fairwood
Our data shows 40 appliance repair companies inside a 30-mile radius of Fairwood. Other nearby bases include Kent (13), Renton (12), and Issaquah (4). Distances run up to about 8 miles. Dependable Renton Appliance Repair is the nearest, roughly 0.5 miles from Fairwood. No company within 30 miles of Fairwood names GE in its listing, so the list adds matches from farther out and the closest appliance repair companies. Across 32 rated companies, the average public rating is 4.7 stars.
Companies are shown by relevance and distance from Fairwood. A mention does not mean manufacturer certification, so ask each company about its experience with your dryer.
| Open on Saturdays (per listing) | 32 |
|---|---|
| With 4.5+ stars and at least 10 reviews | 21 |
| Companies within 30 miles | 60 |
| Mention GE | 0 |
| Show laundry appliance work | 12 |
| Three nearest companies, miles away | 0.5, 1.9, 2.9 |
First up for Fairwood: GE Monogram Repair Kirkland (17.5 miles away, based in Kirkland, 5.0 stars from 21 reviews, lists Saturday hours); Sears Appliance Repair (65.0 miles away, based in Chehalis, 4.4 stars from 134 reviews, lists Saturday hours); Expert Appliance Repair (6.4 miles away, based in Seattle, 5.0 stars from 1,139 reviews); Troubleshooters Appliance Repair (6.8 miles away, based in Newcastle, 4.9 stars from 136 reviews, lists Saturday hours).
GE Dryer Lines and Features
What a GE Dryer Technician Deals With
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
GE Dryer Symptoms and First Checks
- Check Vent alert. GE says to unplug the dryer, disconnect and vacuum the duct, and make sure the outside hood damper moves freely. Source: GE Appliances - Dryer - Check Vent Sensor Alert
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
Reading a GE Dryer Error Code
| Code | What it means |
|---|---|
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Outside of the cabinet gets unusually hot
- Burning or hot smell during a cycle
- Dryer will not start when you press Start
What a Dryer Repair Technician Checks
Owner Care for GE Dryers
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Brand guides: GE Dryer Not Heating: What to Check.
What GE Dryer Repairs Cost
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Gas valve coil replacement (gas dryer): $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Heating element replacement: $150–$350 Source: Fixr - How much does it cost to repair a dryer?
- Drum belt replacement: $150–$250 Source: Fixr - How much does it cost to repair a dryer?
- Technician service / diagnostic fee, dryer: $50–$80 per visit Source: Fixr - How much does it cost to repair a dryer?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Before the Technician Arrives
- Whether the dryer is gas or electric
- Any error code on the display
- How long the vent run is and where it exits the house
Dryer Notes for Fairwood, WA
Most dryer calls in Fairwood come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Washington's Department of Labor & Industries issues an appliance repair (07D) specialty electrician certificate that covers like-for-like repair and replacement of self-contained appliances such as ovens on an unchanged circuit, but excludes branch-circuit wiring and plumbing work. Source: WAC 296-46B-920, Electrical/telecommunications license/certificate types and scope of work
In Washington, you can check a license with the L&I Verify a Contractor, Tradesperson or Business or report a problem to the Washington State Office of the Attorney General, Consumer Protection.
Before You Book in Fairwood
- If a part has to be ordered, how soon can you come back to finish?
- Can you look at the washer on the same visit if it is acting up too?
- Do you work on gas dryers, and who handles anything involving the gas line?
GE Dryer Repair FAQs: Fairwood, WA
Why does my dryer take so long to dry?
What should I do about a GE error code?
Is my GE dryer worth repairing?
Other Dryer Repair in Fairwood
GE Dryer Repair in Nearby Cities
Clean the lint screen, check the vent hood outside and note the model number before calling. It rules out the simple causes and speeds up a GE repair.