Most GE dryer repairs in Hudson involve the same few systems: heat, airflow, the drum drive and the controls. The Hudson list starts with companies that name GE, followed by other appliance repair companies that list dryer work.
This is an independent directory. We are not affiliated with GE, and the technicians listed are independent repair companies, not the manufacturer.
GE Dryer Repair Near Hudson
Within 30 miles of Hudson there are 40 appliance repair companies in our data. The rest are spread across St Paul (7), Maplewood (4), and West St Paul (4). Eagle Appliance Repair | Lakeland is the nearest, roughly 2.4 miles from Hudson. No company within 90 miles of Hudson mentions GE by name, so these are the nearest appliance repair companies. Most work on several brands, so ask about yours. Rated companies nearby average 4.5 stars across 27 businesses.
Companies are shown by relevance and distance from Hudson. A mention does not mean manufacturer certification, so ask each company about its experience with your dryer.
| Mention GE | 0 |
|---|---|
| Listing Saturday hours | 47 |
| Appliance repair companies in range (30 mi) | 60 |
| Distance to the three closest (mi) | 2.4, 7.2, 7.6 |
| With 4.5+ stars and at least 10 reviews | 24 |
| Show laundry appliance work | 14 |
First up for Hudson: Warners' Stellian Appliance (12.1 miles away, based in Woodbury, 4.7 stars from 2,220 reviews, lists Saturday hours); Omega Force Appliance Repair (20.5 miles away, based in St Paul, 4.9 stars from 678 reviews, lists Saturday hours); Super Care Appliance Repair (17.8 miles away, based in West St Paul, 4.9 stars from 1,075 reviews, lists Saturday hours); Sears Appliance Repair (7.9 miles away, based in River Falls, 4.5 stars from 183 reviews, lists Saturday hours).
GE Dryer Features Technicians Work On
How GE Dryers Are Built
GE allows only rigid or flexible metal vent duct and says plastic flexible duct is not acceptable because it collapses, cuts airflow and can collect water. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
GE Dryer Symptoms and First Checks
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
- Dryer will not run or start. GE's first check is that the dryer plug is pushed fully into the wall outlet. Source: GE Appliances - Dryer - Will Not Run or Start
GE Dryer Error Codes
| Code | What it means |
|---|---|
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
Signs Your GE Dryer Needs a Technician
- Cycles take two or three runs to finish
- Dryer shuts off a few minutes into the cycle
- Burning or hot smell during a cycle
What a Dryer Repair Technician Checks
Owner Care for GE Dryers
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
Brand guides: GE Dryer Not Heating: What to Check.
Budgeting for a GE Dryer Repair
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Drum bearing replacement: $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Control board (part only): $90–$280 Source: Angi - How Much Does Dryer Repair Cost?
- Drum belt replacement: $150–$250 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair (most homeowners): $100–$430 Source: Angi - How Much Does Dryer Repair Cost?
- Appliance technician diagnosis, washer (usually waived if hired for the repair): $50–$100 per visit Source: Fixr - How much does it cost to repair a washing machine?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Before the Technician Arrives
- Any error code on the display
- The brand, model and serial number from the label inside the door or on the back panel
- What happens when you press Start (no response, hum, runs with no heat, stops early)
Dryer Notes for Hudson, WI
Most dryer calls in Hudson come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Wisconsin has no separate appliance repair license; plumbing licensing covers appliances connected to water supply systems, including water heaters, but exempts minor repairs to appliances and repair or replacement of gas or electrical control valves and devices. Source: DSPS: Plumbing License Laws in Wisconsin
In Wisconsin, you can check a license with the Wisconsin DSPS LicensE credential lookup or report a problem to the Wisconsin Department of Agriculture, Trade and Consumer Protection (DATCP), Bureau of Consumer Protection.
Hiring a Dryer Repair Company in Hudson
- Will you check the vent and lint path as part of the visit?
- Do you work on gas dryers, and who handles anything involving the gas line?
- What is the service call or diagnostic fee, and is it applied to the repair?
GE Dryer Repair FAQs: Hudson, WI
Why does my GE dryer show an error code?
Do you work for GE?
Which Hudson technicians work on GE?
Related Repair Pages for Hudson
More GE Dryer Repair Pages Nearby
Clean the lint screen, check the vent hood outside and note the model number before calling. It rules out the simple causes and speeds up a GE repair.