If your GE dryer has stopped heating, stopped tumbling or started throwing an error code, the technician you call should know the model line. Below are independent repair companies serving Oakdale, with those that mention GE first, then the nearest dryer repair companies.
Washer and Dryer Repair is independent and not affiliated with GE. Listed companies are independent technicians who repair GE dryers and other brands.
Who Works on GE Dryers Near Oakdale
We found 40 appliance repair companies within 30 miles of Oakdale. 1 list an address in Oakdale, and other nearby bases include St Paul (10), Maplewood (4), and West St Paul (4). Distances run up to about 12 miles. None of the repair companies near Oakdale name GE in their listings, so we show the closest appliance repair companies. Ask each one about your model before booking. Nearest on the list: David Hayes Appliance Service Specialists, around 2.2 miles out. Rated companies nearby average 4.3 stars across 28 businesses.
Companies are shown by relevance and distance from Oakdale. A mention does not mean manufacturer certification, so ask each company about its experience with your dryer.
| Listing Saturday hours | 48 |
|---|---|
| Three nearest companies, miles away | 2.2, 2.8, 3.3 |
| Mention GE | 0 |
| List dryer or washer & dryer work | 15 |
| With 4.5+ stars and at least 10 reviews | 24 |
| Repair companies inside 30 miles | 60 |
Closest matches for Oakdale: Warners' Stellian Appliance (4.4 miles away, based in Woodbury, 4.7 stars from 2,220 reviews, lists Saturday hours); Omega Force Appliance Repair (9.4 miles away, based in St Paul, 4.9 stars from 678 reviews, lists Saturday hours); Warners' Stellian Appliance (10.0 miles away, based in St Paul, 4.8 stars from 2,260 reviews, lists Saturday hours); Super Care Appliance Repair (8.4 miles away, based in West St Paul, 4.9 stars from 1,075 reviews, lists Saturday hours).
GE Dryer Lines and Features
How GE Dryers Are Built
Some GE dryers have an airflow sensor that shows a Check Vent alert when exhaust airflow drops, which usually means the vent is blocked. Source: GE Appliances - Dryer - Check Vent Sensor Alert
GE allows only rigid or flexible metal vent duct and says plastic flexible duct is not acceptable because it collapses, cuts airflow and can collect water. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
What GE Says to Check First
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
- Dryer takes too long to dry. GE points first to venting (metal duct, no kinks, clear wall cap) and a clean lint filter, then to load size, dryer level and washer spin speed. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Reading a GE Dryer Error Code
| Code | What it means |
|---|---|
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
When to Call for GE Dryer Repair
- Drum will not turn even though you hear a hum
- Outside of the cabinet gets unusually hot
- Dryer will not start when you press Start
What a Dryer Repair Technician Checks
Care GE Recommends for Its Dryers
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Brand guides: GE Dryer Not Heating: What to Check.
GE Dryer Repair Cost Ranges
A GE dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Thermal fuse repair: $80–$130 Source: Angi - How Much Does It Cost to Repair a Dryer?
- Thermostat replacement: $100–$260 Source: Fixr - How much does it cost to repair a dryer?
- Drive motor replacement: $250–$450 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair: $100–$200 Source: Fixr - How much does it cost to repair a dryer?
- Appliance technician diagnosis, washer (usually waived if hired for the repair): $50–$100 per visit Source: Fixr - How much does it cost to repair a washing machine?
A dryer that keeps needing repairs despite regular maintenance is usually cheaper to replace. Source: Angi - How Much Does Dryer Repair Cost?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
What to Have Ready for a GE Dryer Call
- Whether the dryer is gas or electric
- What happens when you press Start (no response, hum, runs with no heat, stops early)
- The brand, model and serial number from the label inside the door or on the back panel
What Oakdale Owners Should Know
Most dryer calls in Oakdale come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Minnesota has no state license for mechanical contractors or their workers; businesses contracting for gas, heating, cooling or refrigeration work file a mechanical contractor bond with the Department of Labor and Industry, and some cities require their own licenses or competency cards. Source: DLI: Mechanical contractor bond requirements
The state does not license gas fitters; contractors doing gas work must be bonded with the Department of Labor and Industry, and cities such as Minneapolis and St. Paul set their own gas fitter licensing. Source: DLI: Mechanical contractor bond requirements
Before You Book in Oakdale
- What is the service call or diagnostic fee, and is it applied to the repair?
- Will you check the vent and lint path as part of the visit?
- Can you look at the washer on the same visit if it is acting up too?
GE Dryer Repair FAQs: Oakdale, MN
Why do my clothes come out damp?
Why is my dryer running but not heating?
Is this GE customer service?
Related Repair Pages for Oakdale
GE Dryer Repair Near Oakdale
Clean the lint screen, check the vent hood outside and note the model number before calling. It rules out the simple causes and speeds up a GE repair.