A GE dryer shares most of its parts with other dryers, but its controls, error codes and sensor-dry cycles are specific to the brand. Below are independent repair companies serving St. Cloud, with those that mention GE first, then the nearest dryer repair companies.
Independent listings only: Washer and Dryer Repair is not affiliated with or endorsed by GE. If your dryer is still under manufacturer coverage, contact GE directly.
Independent GE Dryer Technicians, St. Cloud MN
Our data shows 15 appliance repair companies inside a 30-mile radius of St. Cloud. The rest are spread across St Cloud (6), Sauk Rapids (2), and Kimball (1). The farthest listed company is about 30 miles out. The closest is Omega Force Appliance Repair, about 0.3 miles away. None of the companies within 30 miles mention GE by name, so we include matching companies from a longer drive plus the nearest appliance repair companies. The 15 rated companies in range average 4.7 stars.
Companies are shown by relevance and distance from St. Cloud. A mention does not mean manufacturer certification, so ask each company about its experience with your dryer.
| Open on Saturdays (per listing) | 8 |
|---|---|
| Mention GE | 0 |
| List dryer or washer & dryer work | 4 |
| Companies within 30 miles | 15 |
| Three nearest companies, miles away | 0.3, 1.3, 1.5 |
| Rated 4.5 stars or higher (10+ reviews) | 7 |
First up for St. Cloud: Sears Appliance Repair (51.5 miles away, based in Willmar, 4.5 stars from 37 reviews, lists Saturday hours); Omega Force Appliance Repair (0.3 miles away, based in St Cloud, 4.8 stars from 199 reviews, lists Saturday hours); Crosstown Appliance Repair (17.9 miles away, based in Richmond, 4.8 stars from 154 reviews); Sears Appliance Repair (2.4 miles away, based in St Cloud, 4.4 stars from 86 reviews, lists Saturday hours).
Know Your GE Dryer
What Makes GE Dryer Repairs Different
GE allows only rigid or flexible metal vent duct and says plastic flexible duct is not acceptable because it collapses, cuts airflow and can collect water. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
GE Dryer Symptoms and First Checks
- Dryer takes too long to dry. GE points first to venting (metal duct, no kinks, clear wall cap) and a clean lint filter, then to load size, dryer level and washer spin speed. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
Reading a GE Dryer Error Code
| Code | What it means |
|---|---|
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Dryer will not start when you press Start
- Burning or hot smell during a cycle
- Dryer shuts off a few minutes into the cycle
How a Dryer Service Call Usually Goes in St. Cloud
Care GE Recommends for Its Dryers
- Inspect and clean the exhaust duct at least once a year by unplugging the dryer, disconnecting the duct and vacuuming it, and check that the outside hood flaps move freely with no nests inside. Source: GE Appliances - Dryer - How to Clean Exhaust / Vent Duct
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Brand guides: GE Dryer Not Heating: What to Check.
Budgeting for a GE Dryer Repair
A GE dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Door switch replacement: $50–$150 Source: Fixr - How much does it cost to repair a dryer?
- Thermal fuse repair: $80–$130 Source: Angi - How Much Does It Cost to Repair a Dryer?
- Drive motor replacement: $250–$450 Source: Fixr - How much does it cost to repair a dryer?
- Appliance technician diagnosis, washer (usually waived if hired for the repair): $50–$100 per visit Source: Fixr - How much does it cost to repair a washing machine?
Replacement makes more sense once a dryer is about 10 years old or past half its expected lifespan. Source: Fixr - How much does it cost to repair a dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Before the Technician Arrives
- Whether the dryer is gas or electric
- The brand, model and serial number from the label inside the door or on the back panel
- Any error code on the display
Dryer Notes for St. Cloud, MN
Most dryer calls in St. Cloud come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Minnesota has no state license for mechanical contractors or their workers; businesses contracting for gas, heating, cooling or refrigeration work file a mechanical contractor bond with the Department of Labor and Industry, and some cities require their own licenses or competency cards. Source: DLI: Mechanical contractor bond requirements
The state does not license gas fitters; contractors doing gas work must be bonded with the Department of Labor and Industry, and cities such as Minneapolis and St. Paul set their own gas fitter licensing. Source: DLI: Mechanical contractor bond requirements
Before You Book in St. Cloud
- Do you work on gas dryers, and who handles anything involving the gas line?
- Can you give a written estimate before ordering parts?
- Is your company licensed where my state requires it, and insured?
GE Dryer Repair FAQs: St. Cloud, MN
What should I do about a GE error code?
Why does my dryer take so long to dry?
Is this GE customer service?
Should I repair or replace my GE dryer?
More Laundry Repair in St. Cloud, MN
More GE Dryer Repair Pages Nearby
Clean the lint screen, check the vent hood outside and note the model number before calling. It rules out the simple causes and speeds up a GE repair.