A GE dryer shares most of its parts with other dryers, but its controls, error codes and sensor-dry cycles are specific to the brand. Below are independent repair companies serving Bloomington, with those that mention GE first, then the nearest dryer repair companies.
Independent listings only: Washer and Dryer Repair is not affiliated with or endorsed by GE. If your dryer is still under manufacturer coverage, contact GE directly.
GE Dryer Repair Near Bloomington
Our data shows 40 appliance repair companies inside a 30-mile radius of Bloomington. 4 of them are based in Bloomington itself, and other nearby bases include Minneapolis (8), Burnsville (5), and Eden Prairie (5). The farthest listed company is about 11 miles out. Nearest on the list: Advanced Appliance Repair Bloomington., around 1.4 miles out. No company within 30 miles of Bloomington names GE in its listing, so the list adds matches from farther out and the closest appliance repair companies. Rated companies nearby average 4.4 stars across 29 businesses.
Listings come from public business data. A brand or service mention means the company names it in its listing or website; it is not a certification. Verify experience, licensing and insurance before hiring.
| Open on Saturdays (per listing) | 48 |
|---|---|
| Mention GE | 0 |
| Distance to the three closest (mi) | 1.4, 1.4, 1.6 |
| List dryer or washer & dryer work | 19 |
| Repair companies inside 30 miles | 60 |
| Rated 4.5 stars or higher (10+ reviews) | 26 |
At the top of the Bloomington list: Sears Appliance Repair (86.4 miles away, based in Willmar, 4.5 stars from 37 reviews, lists Saturday hours); Warners' Stellian Appliance (8.0 miles away, based in Shakopee, 4.7 stars from 1,015 reviews, lists Saturday hours); Warners' Stellian Appliance (8.1 miles away, based in Apple Valley, 4.7 stars from 1,914 reviews, lists Saturday hours); Tony's Appliance (5.7 miles away, based in Burnsville, 4.9 stars from 1,214 reviews, lists Saturday hours).
Know Your GE Dryer
How GE Dryers Are Built
Some GE dryers have an airflow sensor that shows a Check Vent alert when exhaust airflow drops, which usually means the vent is blocked. Source: GE Appliances - Dryer - Check Vent Sensor Alert
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
What GE Says to Check First
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
- Dryer will not run or start. GE's first check is that the dryer plug is pushed fully into the wall outlet. Source: GE Appliances - Dryer - Will Not Run or Start
Reading a GE Dryer Error Code
| Code | What it means |
|---|---|
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Burning or hot smell during a cycle
- Dryer will not start when you press Start
- Outside of the cabinet gets unusually hot
Inside a Dryer Repair Visit
Care GE Recommends for Its Dryers
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
- Inspect and clean the exhaust duct at least once a year by unplugging the dryer, disconnecting the duct and vacuuming it, and check that the outside hood flaps move freely with no nests inside. Source: GE Appliances - Dryer - How to Clean Exhaust / Vent Duct
Brand guides: GE Dryer Not Heating: What to Check.
Budgeting for a GE Dryer Repair
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Gas valve coil replacement (gas dryer): $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Door switch replacement: $50–$150 Source: Fixr - How much does it cost to repair a dryer?
- Timer replacement: $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Drum belt replacement: $150–$250 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair: $100–$200 Source: Fixr - How much does it cost to repair a dryer?
- Technician service / diagnostic fee, dryer: $50–$80 per visit Source: Fixr - How much does it cost to repair a dryer?
A dryer that keeps needing repairs despite regular maintenance is usually cheaper to replace. Source: Angi - How Much Does Dryer Repair Cost?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Getting Ready for the Repair
- The brand, model and serial number from the label inside the door or on the back panel
- How long the vent run is and where it exits the house
- What happens when you press Start (no response, hum, runs with no heat, stops early)
Around Bloomington
Most dryer calls in Bloomington come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Minnesota has no state license for mechanical contractors or their workers; businesses contracting for gas, heating, cooling or refrigeration work file a mechanical contractor bond with the Department of Labor and Industry, and some cities require their own licenses or competency cards. Source: DLI: Mechanical contractor bond requirements
In Minnesota, you can check a license with the DLI License and Registration Lookup or report a problem to the Minnesota Attorney General's Office, Consumer Assistance.
Before You Book in Bloomington
- What is the service call or diagnostic fee, and is it applied to the repair?
- Can you give a written estimate before ordering parts?
- How often do you repair GE dryers, and do you carry common parts on the truck?
GE Dryer Repair FAQs: Bloomington, MN
Why is my dryer running but not heating?
Which Bloomington technicians work on GE?
Should I repair or replace my GE dryer?
Why does my GE dryer show an error code?
Related Repair Pages for Bloomington
GE Dryer Repair in Nearby Cities
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.