Most GE dryer repairs in Richfield involve the same few systems: heat, airflow, the drum drive and the controls. The Richfield list starts with companies that name GE, followed by other appliance repair companies that list dryer work.
This is an independent directory. We are not affiliated with GE, and the technicians listed are independent repair companies, not the manufacturer.
GE Dryer Repair Near Richfield
Our data shows 40 appliance repair companies inside a 30-mile radius of Richfield. The rest are spread across Minneapolis (11), St Paul (6), and Burnsville (5). Distances run up to about 10 miles. Nearest on the list: Appliance Repair & Support, around 2.2 miles out. No company within 30 miles of Richfield names GE in its listing, so the list adds matches from farther out and the closest appliance repair companies. The 29 rated companies in range average 4.4 stars.
Companies are shown by relevance and distance from Richfield. A mention does not mean manufacturer certification, so ask each company about its experience with your dryer.
| Open on Saturdays (per listing) | 47 |
|---|---|
| Mention GE | 0 |
| With 4.5+ stars and at least 10 reviews | 25 |
| Show laundry appliance work | 18 |
| Appliance repair companies in range (30 mi) | 60 |
| Distance to the three closest (mi) | 2.2, 2.5, 2.5 |
At the top of the Richfield list: Sears Appliance Repair (87.3 miles away, based in Willmar, 4.5 stars from 37 reviews, lists Saturday hours); Omega Force Appliance Repair (8.4 miles away, based in St Paul, 4.9 stars from 678 reviews, lists Saturday hours); Warners' Stellian Appliance (9.8 miles away, based in St Paul, 4.8 stars from 2,260 reviews, lists Saturday hours); Super Care Appliance Repair (9.9 miles away, based in West St Paul, 4.9 stars from 1,075 reviews, lists Saturday hours).
GE Dryer Lines and Features
What a GE Dryer Technician Deals With
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Common GE Dryer Problems
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
Reading a GE Dryer Error Code
| Code | What it means |
|---|---|
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
Signs Your GE Dryer Needs a Technician
- Drum turns but the air stays cool
- Squealing, thumping or grinding while it runs
- Clothes still damp after a full cycle
What a Dryer Repair Technician Checks
Care GE Recommends for Its Dryers
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Brand guides: GE Dryer Not Heating: What to Check.
GE Dryer Repair Cost Ranges
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Drum roller replacement: $100–$150 Source: Fixr - How much does it cost to repair a dryer?
- Heating element replacement: $150–$350 Source: Fixr - How much does it cost to repair a dryer?
- Thermostat replacement: $100–$260 Source: Fixr - How much does it cost to repair a dryer?
- Control board (part only): $90–$280 Source: Angi - How Much Does Dryer Repair Cost?
- Typical dryer repair: $100–$200 Source: Fixr - How much does it cost to repair a dryer?
- Technician service / diagnostic fee, dryer: $50–$80 per visit Source: Fixr - How much does it cost to repair a dryer?
A dryer that keeps needing repairs despite regular maintenance is usually cheaper to replace. Source: Angi - How Much Does Dryer Repair Cost?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
What to Have Ready for a GE Dryer Call
- Any error code on the display
- Whether the dryer is gas or electric
- How long the vent run is and where it exits the house
Around Richfield
Most dryer calls in Richfield come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Minnesota has no state license for mechanical contractors or their workers; businesses contracting for gas, heating, cooling or refrigeration work file a mechanical contractor bond with the Department of Labor and Industry, and some cities require their own licenses or competency cards. Source: DLI: Mechanical contractor bond requirements
The state does not license gas fitters; contractors doing gas work must be bonded with the Department of Labor and Industry, and cities such as Minneapolis and St. Paul set their own gas fitter licensing. Source: DLI: Mechanical contractor bond requirements
Questions to Ask a Richfield Technician
- Can you give a written estimate before ordering parts?
- Is your company licensed where my state requires it, and insured?
- Can you look at the washer on the same visit if it is acting up too?
GE Dryer Repair FAQs: Richfield, MN
Why does my GE dryer show an error code?
How do I find a technician who knows GE dryers?
Why is my dryer running but not heating?
Is this GE customer service?
More Laundry Repair in Richfield, MN
GE Dryer Repair in Nearby Cities
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.