A GE dryer shares most of its parts with other dryers, but its controls, error codes and sensor-dry cycles are specific to the brand. Below are independent repair companies serving Hopkins, with those that mention GE first, then the nearest dryer repair companies.
This is an independent directory. We are not affiliated with GE, and the technicians listed are independent repair companies, not the manufacturer.
Independent GE Dryer Technicians, Hopkins MN
40 repair companies serve Hopkins from within 30 miles. 5 list an address in Hopkins, and other nearby bases include Minneapolis (12), Eden Prairie (5), and Plymouth (4). None of the companies within 30 miles mention GE by name, so we include matching companies from a longer drive plus the nearest appliance repair companies. Nearest on the list: Beacon Appliance Repair Solution, around 0.3 miles out. Across 23 rated companies, the average public rating is 4.4 stars.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| Repair companies inside 30 miles | 60 |
|---|---|
| Listing Saturday hours | 48 |
| Show laundry appliance work | 14 |
| Rated 4.5 stars or higher (10+ reviews) | 21 |
| Mention GE | 0 |
| Three nearest companies, miles away | 0.3, 0.8, 1.0 |
At the top of the Hopkins list: Sears Appliance Repair (80.8 miles away, based in Willmar, 4.5 stars from 37 reviews, lists Saturday hours); Warners' Stellian Appliance (10.2 miles away, based in Shakopee, 4.7 stars from 1,015 reviews, lists Saturday hours); AMA Appliance Service (1.1 miles away, 5.0 stars from 82 reviews); Warners' Stellian Appliance Outlet (10.2 miles away, based in Minneapolis, 4.7 stars from 670 reviews, lists Saturday hours).
GE Dryer Features Technicians Work On
How GE Dryers Are Built
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
GE Dryer Symptoms and First Checks
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
- Dryer takes too long to dry. GE points first to venting (metal duct, no kinks, clear wall cap) and a clean lint filter, then to load size, dryer level and washer spin speed. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Reading a GE Dryer Error Code
| Code | What it means |
|---|---|
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
When to Call for GE Dryer Repair
- Dryer will not start when you press Start
- Outside of the cabinet gets unusually hot
- Burning or hot smell during a cycle
Inside a Dryer Repair Visit
Care GE Recommends for Its Dryers
- Inspect and clean the exhaust duct at least once a year by unplugging the dryer, disconnecting the duct and vacuuming it, and check that the outside hood flaps move freely with no nests inside. Source: GE Appliances - Dryer - How to Clean Exhaust / Vent Duct
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
Brand guides: GE Dryer Not Heating: What to Check.
GE Dryer Repair Cost Ranges
A GE dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Control board (part only): $90–$280 Source: Angi - How Much Does Dryer Repair Cost?
- Drum roller replacement: $100–$150 Source: Fixr - How much does it cost to repair a dryer?
- Drum belt replacement: $150–$250 Source: Fixr - How much does it cost to repair a dryer?
- Door switch replacement: $50–$150 Source: Fixr - How much does it cost to repair a dryer?
- Dryer not heating (repair by symptom): $80–$420 Source: Angi - How Much Does Dryer Repair Cost?
- Appliance technician diagnosis, washer (usually waived if hired for the repair): $50–$100 per visit Source: Fixr - How much does it cost to repair a washing machine?
A dryer that keeps needing repairs despite regular maintenance is usually cheaper to replace. Source: Angi - How Much Does Dryer Repair Cost?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Before the Technician Arrives
- How long the vent run is and where it exits the house
- What happens when you press Start (no response, hum, runs with no heat, stops early)
- Whether the dryer is gas or electric
Dryer Notes for Hopkins, MN
Most dryer calls in Hopkins come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Minnesota has no state license for mechanical contractors or their workers; businesses contracting for gas, heating, cooling or refrigeration work file a mechanical contractor bond with the Department of Labor and Industry, and some cities require their own licenses or competency cards. Source: DLI: Mechanical contractor bond requirements
The state does not license gas fitters; contractors doing gas work must be bonded with the Department of Labor and Industry, and cities such as Minneapolis and St. Paul set their own gas fitter licensing. Source: DLI: Mechanical contractor bond requirements
How to Choose a Dryer Technician Near Hopkins
- How often do you repair GE dryers, and do you carry common parts on the truck?
- What guarantee do you give on parts and labor?
- Do you work on gas dryers, and who handles anything involving the gas line?
GE Dryer Repair FAQs: Hopkins, MN
How do I find a technician who knows GE dryers?
Why is my dryer running but not heating?
Do you work for GE?
Other Dryer Repair in Hopkins
More GE Dryer Repair Pages Nearby
Write down any error code your GE dryer shows and when it appears. It helps a Hopkins technician bring the right parts.