Most GE dryer repairs in Minnetonka involve the same few systems: heat, airflow, the drum drive and the controls. The Minnetonka list starts with companies that name GE, followed by other appliance repair companies that list dryer work.
This is an independent directory. We are not affiliated with GE, and the technicians listed are independent repair companies, not the manufacturer.
GE Dryer Repair Near Minnetonka
We found 40 appliance repair companies within 30 miles of Minnetonka. 2 list an address in Minnetonka, and other nearby bases include Minneapolis (11), Hopkins (5), and Eden Prairie (5). The farthest listed company is about 11 miles out. Nearest on the list: AMA Appliance Service, around 1.7 miles out. No company within 30 miles of Minnetonka names GE in its listing, so the list adds matches from farther out and the closest appliance repair companies. Across 22 rated companies, the average public rating is 4.5 stars.
Companies are shown by relevance and distance from Minnetonka. A mention does not mean manufacturer certification, so ask each company about its experience with your dryer.
| Rated 4.5 stars or higher (10+ reviews) | 20 |
|---|---|
| Companies within 30 miles | 60 |
| Three nearest companies, miles away | 1.7, 1.8, 2.4 |
| Mention GE | 0 |
| List dryer or washer & dryer work | 14 |
| Listing Saturday hours | 47 |
At the top of the Minnetonka list: Sears Appliance Repair (78.1 miles away, based in Willmar, 4.5 stars from 37 reviews, lists Saturday hours); Warners' Stellian Appliance (10.2 miles away, based in Shakopee, 4.7 stars from 1,015 reviews, lists Saturday hours); AMA Appliance Service (1.7 miles away, based in Hopkins, 5.0 stars from 82 reviews); Twin Cities Appliance Service Center Inc (2.4 miles away, based in Hopkins, 4.9 stars from 1,837 reviews).
GE Dryer Lines and Features
How GE Dryers Are Built
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
GE Dryer Symptoms and First Checks
- Check Vent alert. GE says to unplug the dryer, disconnect and vacuum the duct, and make sure the outside hood damper moves freely. Source: GE Appliances - Dryer - Check Vent Sensor Alert
- Gas dryer runs but does not heat. GE says to confirm a real drying cycle and temperature are selected, keep the front of the dryer unblocked, check the dedicated 120V outlet, and on new installs make sure the gas line is turned on. Source: GE Appliances - Gas Dryer - Runs But Does Not Heat
What GE Dryer Codes Mean
| Code | What it means |
|---|---|
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Clothes still damp after a full cycle
- Squealing, thumping or grinding while it runs
- Dryer will not start when you press Start
How a Dryer Service Call Usually Goes in Minnetonka
Keeping a GE Dryer Running
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
- Inspect and clean the exhaust duct at least once a year by unplugging the dryer, disconnecting the duct and vacuuming it, and check that the outside hood flaps move freely with no nests inside. Source: GE Appliances - Dryer - How to Clean Exhaust / Vent Duct
Brand guides: GE Dryer Not Heating: What to Check.
GE Dryer Repair Cost Ranges
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Door switch replacement: $50–$150 Source: Fixr - How much does it cost to repair a dryer?
- Drum bearing replacement: $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Thermostat replacement: $100–$260 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair (most homeowners): $100–$430 Source: Angi - How Much Does Dryer Repair Cost?
- Service call fee (may be waived if the technician does the repair): $50–$80 per visit Source: Angi - How Much Does It Cost to Repair a Dryer?
A dryer that keeps needing repairs despite regular maintenance is usually cheaper to replace. Source: Angi - How Much Does Dryer Repair Cost?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Before the Technician Arrives
- Any error code on the display
- Whether the dryer is gas or electric
- What happens when you press Start (no response, hum, runs with no heat, stops early)
Around Minnetonka
Most dryer calls in Minnetonka come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Minnesota has no state license for mechanical contractors or their workers; businesses contracting for gas, heating, cooling or refrigeration work file a mechanical contractor bond with the Department of Labor and Industry, and some cities require their own licenses or competency cards. Source: DLI: Mechanical contractor bond requirements
The state does not license gas fitters; contractors doing gas work must be bonded with the Department of Labor and Industry, and cities such as Minneapolis and St. Paul set their own gas fitter licensing. Source: DLI: Mechanical contractor bond requirements
Before You Book in Minnetonka
- Do you work on gas dryers, and who handles anything involving the gas line?
- Is your company licensed where my state requires it, and insured?
- What is the service call or diagnostic fee, and is it applied to the repair?
GE Dryer Repair FAQs: Minnetonka, MN
Why does my dryer take so long to dry?
What makes a dryer stop heating?
Should I repair or replace my GE dryer?
How do I find a technician who knows GE dryers?
More Laundry Repair in Minnetonka, MN
More GE Dryer Repair Pages Nearby
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.