If your GE dryer has stopped heating, stopped tumbling or started throwing an error code, the technician you call should know the model line. We flag companies whose listing or website mentions GE and fill in with nearby dryer repair companies so you always have options.
Washer and Dryer Repair is independent and not affiliated with GE. Listed companies are independent technicians who repair GE dryers and other brands.
GE Dryer Repair Near St. Louis Park
Within 30 miles of St. Louis Park there are 40 appliance repair companies in our data. The rest are spread across Minneapolis (12), Hopkins (5), and Eden Prairie (5). The farthest listed company is about 10 miles out. The closest is North Metro appliance, about 1.8 miles away. None of the companies within 30 miles mention GE by name, so we include matching companies from a longer drive plus the nearest appliance repair companies. Rated companies nearby average 4.3 stars across 25 businesses.
Companies are shown by relevance and distance from St. Louis Park. A mention does not mean manufacturer certification, so ask each company about its experience with your dryer.
| Open on Saturdays (per listing) | 47 |
|---|---|
| With 4.5+ stars and at least 10 reviews | 20 |
| List dryer or washer & dryer work | 12 |
| Repair companies inside 30 miles | 60 |
| Distance to the three closest (mi) | 1.8, 2.8, 3.2 |
| Mention GE | 0 |
The leading options for St. Louis Park are Sears Appliance Repair (82.5 miles away, based in Willmar, 4.5 stars from 37 reviews, lists Saturday hours); Warners' Stellian Appliance (10.1 miles away, based in St Paul, 4.8 stars from 2,260 reviews, lists Saturday hours); AMA Appliance Service (3.5 miles away, based in Hopkins, 5.0 stars from 82 reviews); Warners' Stellian Appliance Outlet (7.7 miles away, based in Minneapolis, 4.7 stars from 670 reviews, lists Saturday hours).
Know Your GE Dryer
What a GE Dryer Technician Deals With
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
Common GE Dryer Problems
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
- Check Vent alert. GE says to unplug the dryer, disconnect and vacuum the duct, and make sure the outside hood damper moves freely. Source: GE Appliances - Dryer - Check Vent Sensor Alert
What GE Dryer Codes Mean
| Code | What it means |
|---|---|
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
Signs Your GE Dryer Needs a Technician
- Squealing, thumping or grinding while it runs
- Dryer shuts off a few minutes into the cycle
- Drum will not turn even though you hear a hum
How a Dryer Service Call Usually Goes in St. Louis Park
Owner Care for GE Dryers
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
Brand guides: GE Dryer Not Heating: What to Check.
Budgeting for a GE Dryer Repair
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Drive motor replacement: $250–$450 Source: Fixr - How much does it cost to repair a dryer?
- Thermostat replacement: $100–$260 Source: Fixr - How much does it cost to repair a dryer?
- Door switch replacement: $50–$150 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair: $100–$200 Source: Fixr - How much does it cost to repair a dryer?
- Technician service / diagnostic fee, dryer: $50–$80 per visit Source: Fixr - How much does it cost to repair a dryer?
Replacement makes more sense once a dryer is about 10 years old or past half its expected lifespan. Source: Fixr - How much does it cost to repair a dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Getting Ready for the Repair
- What happens when you press Start (no response, hum, runs with no heat, stops early)
- Any error code on the display
- How long the vent run is and where it exits the house
What St. Louis Park Owners Should Know
Most dryer calls in St. Louis Park come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Minnesota has no state license for mechanical contractors or their workers; businesses contracting for gas, heating, cooling or refrigeration work file a mechanical contractor bond with the Department of Labor and Industry, and some cities require their own licenses or competency cards. Source: DLI: Mechanical contractor bond requirements
The state does not license gas fitters; contractors doing gas work must be bonded with the Department of Labor and Industry, and cities such as Minneapolis and St. Paul set their own gas fitter licensing. Source: DLI: Mechanical contractor bond requirements
Before You Book in St. Louis Park
- If a part has to be ordered, how soon can you come back to finish?
- What is the service call or diagnostic fee, and is it applied to the repair?
- How often do you repair GE dryers, and do you carry common parts on the truck?
GE Dryer Repair FAQs: St. Louis Park, MN
Do you work for GE?
How do I find a technician who knows GE dryers?
What makes a dryer stop heating?
Other Dryer Repair in St. Louis Park
More GE Dryer Repair Pages Nearby
Write down any error code your GE dryer shows and when it appears. It helps a St. Louis Park technician bring the right parts.