A GE dryer shares most of its parts with other dryers, but its controls, error codes and sensor-dry cycles are specific to the brand. We flag companies whose listing or website mentions GE and fill in with nearby dryer repair companies so you always have options.
Independent listings only: Washer and Dryer Repair is not affiliated with or endorsed by GE. If your dryer is still under manufacturer coverage, contact GE directly.
Independent GE Dryer Technicians, Burnsville MN
40 repair companies serve Burnsville from within 30 miles. 5 of them are based in Burnsville itself, and other nearby bases include Minneapolis (5), Hopkins (5), and Bloomington (4). RJ Appliance Repair is the nearest, roughly 1.2 miles from Burnsville. None of the companies within 30 miles mention GE by name, so we include matching companies from a longer drive plus the nearest appliance repair companies. Across 30 rated companies, the average public rating is 4.4 stars.
Companies are shown by relevance and distance from Burnsville. A mention does not mean manufacturer certification, so ask each company about its experience with your dryer.
| Listing Saturday hours | 46 |
|---|---|
| Companies within 30 miles | 60 |
| Rated 4.5 stars or higher (10+ reviews) | 24 |
| List dryer or washer & dryer work | 16 |
| Mention GE | 0 |
| Three nearest companies, miles away | 1.2, 1.5, 1.7 |
At the top of the Burnsville list: Sears Appliance Repair (89.3 miles away, based in Willmar, 4.5 stars from 37 reviews, lists Saturday hours); Warners' Stellian Appliance (3.6 miles away, based in Apple Valley, 4.7 stars from 1,914 reviews, lists Saturday hours); Warners' Stellian Appliance (9.1 miles away, based in Shakopee, 4.7 stars from 1,015 reviews, lists Saturday hours); Tony's Appliance (1.8 miles away, 4.9 stars from 1,214 reviews, lists Saturday hours).
GE Dryer Features Technicians Work On
How GE Dryers Are Built
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
GE Dryer Symptoms and First Checks
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
- Dryer takes too long to dry. GE points first to venting (metal duct, no kinks, clear wall cap) and a clean lint filter, then to load size, dryer level and washer spin speed. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Reading a GE Dryer Error Code
| Code | What it means |
|---|---|
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
When to Call for GE Dryer Repair
- Outside of the cabinet gets unusually hot
- Clothes still damp after a full cycle
- Squealing, thumping or grinding while it runs
What Gets Fixed on a Burnsville Dryer Call
Owner Care for GE Dryers
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Brand guides: GE Dryer Not Heating: What to Check.
Budgeting for a GE Dryer Repair
Price the repair before replacing a GE dryer. Published ranges for common jobs:
- Drive motor replacement: $250–$450 Source: Fixr - How much does it cost to repair a dryer?
- Drum bearing replacement: $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Igniter replacement (gas dryer): $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Timer replacement: $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair (most homeowners): $100–$430 Source: Angi - How Much Does Dryer Repair Cost?
- Service call fee (may be waived if the technician does the repair): $50–$80 per visit Source: Angi - How Much Does It Cost to Repair a Dryer?
A dryer that keeps needing repairs despite regular maintenance is usually cheaper to replace. Source: Angi - How Much Does Dryer Repair Cost?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Getting Ready for the Repair
- The brand, model and serial number from the label inside the door or on the back panel
- Whether the dryer is gas or electric
- What happens when you press Start (no response, hum, runs with no heat, stops early)
Local Notes for Burnsville
Most dryer calls in Burnsville come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Minnesota has no state license for mechanical contractors or their workers; businesses contracting for gas, heating, cooling or refrigeration work file a mechanical contractor bond with the Department of Labor and Industry, and some cities require their own licenses or competency cards. Source: DLI: Mechanical contractor bond requirements
The state does not license gas fitters; contractors doing gas work must be bonded with the Department of Labor and Industry, and cities such as Minneapolis and St. Paul set their own gas fitter licensing. Source: DLI: Mechanical contractor bond requirements
How to Choose a Dryer Technician Near Burnsville
- What is the service call or diagnostic fee, and is it applied to the repair?
- Is your company licensed where my state requires it, and insured?
- What guarantee do you give on parts and labor?
GE Dryer Repair FAQs: Burnsville, MN
Is my GE dryer worth repairing?
Which Burnsville technicians work on GE?
Is this GE customer service?
More Laundry Repair in Burnsville, MN
GE Dryer Repair in Nearby Cities
Write down any error code your GE dryer shows and when it appears. It helps a Burnsville technician bring the right parts.