A Kenmore dryer shares most of its parts with other dryers, but its controls, error codes and sensor-dry cycles are specific to the brand. The Burnsville list starts with companies that name Kenmore, followed by other appliance repair companies that list dryer work.
Washer and Dryer Repair is independent and not affiliated with Kenmore. Listed companies are independent technicians who repair Kenmore dryers and other brands.
If you bought your Kenmore at Sears, you do not need to go back to Sears for a repair. Independent technicians near Burnsville work on Kenmore dryers every week.
Who Works on Kenmore Dryers Near Burnsville
We found 40 appliance repair companies within 30 miles of Burnsville. 5 list an address in Burnsville, and other nearby bases include Minneapolis (5), Hopkins (5), and Bloomington (4). Distances run up to about 13 miles. None of the companies within 30 miles mention Kenmore by name, so we include matching companies from a longer drive plus the nearest appliance repair companies. The closest is RJ Appliance Repair, about 1.2 miles away. Rated companies nearby average 4.4 stars across 30 businesses.
Companies are shown by relevance and distance from Burnsville. A mention does not mean manufacturer certification, so ask each company about its experience with your dryer.
| Distance to the three closest (mi) | 1.2, 1.5, 1.7 |
|---|---|
| Mention Kenmore | 0 |
| Listing Saturday hours | 46 |
| With 4.5+ stars and at least 10 reviews | 24 |
| Repair companies inside 30 miles | 60 |
| List dryer or washer & dryer work | 16 |
First up for Burnsville: Sears Appliance Repair (89.3 miles away, based in Willmar, 4.5 stars from 37 reviews, lists Saturday hours); Appliance Repair Pro (3.2 miles away, based in Savage, 5.0 stars from 500 reviews, lists Saturday hours); Tony's Appliance (1.8 miles away, 4.9 stars from 1,214 reviews, lists Saturday hours); Warners' Stellian Appliance (3.6 miles away, based in Apple Valley, 4.7 stars from 1,914 reviews, lists Saturday hours).
Kenmore Dryer Features Technicians Work On
What Makes Kenmore Dryer Repairs Different
Accela Steam dryers connect directly to the household water supply, so the inlet hose and water pressure (20 to 120 psi) become part of a steam-dryer service check. Source: Kenmore - Kenmore Elite Steam Dryer Use & Care Guide (796.8178/796.9178)
What Kenmore Says to Check First
- Dryer not heating. Kenmore says to check for a tripped breaker or blown fuse and, on gas models, confirm the gas supply is on, noting an electric dryer can tumble without heat on a partial circuit. Source: Kenmore - Kenmore Elite Steam Dryer Use & Care Guide (796.8178/796.9178)
- Dryer won't start. Kenmore says to confirm the cord is fully plugged into a grounded outlet and the breaker is intact, and to turn off Control Lock if buttons beep but nothing happens. Source: Kenmore - Kenmore Elite Steam Dryer Use & Care Guide (796.8178/796.9178)
What Kenmore Dryer Codes Mean
| Code | What it means |
|---|---|
| HS (Elite steam dryers) | The humidity (moisture) sensor has failed; the dryer needs service. Source: Kenmore - Kenmore Elite Steam Dryer Use & Care Guide (796.8178/796.9178) |
| d80 / d90 / d95 (Elite steam dryers) | The exhaust ductwork is roughly 80, 90 or 95 percent blocked; stop using the dryer until the vent is cleaned or repaired. Source: Kenmore - Kenmore Elite Steam Dryer Use & Care Guide (796.8178/796.9178) |
| CHECK FILTER (Elite steam dryers) | A reminder to clean the lint filter before the load. Source: Kenmore - Kenmore Elite Steam Dryer Use & Care Guide (796.8178/796.9178) |
Kenmore Dryer Problems Worth a Service Call
- Dryer shuts off a few minutes into the cycle
- Burning or hot smell during a cycle
- Outside of the cabinet gets unusually hot
How a Dryer Service Call Usually Goes in Burnsville
Keeping a Kenmore Dryer Running
- Use only 4-inch rigid or semi-rigid metal duct (no plastic or foil), check it for lint monthly and clean it at least yearly; one Elite steam model allows about 65 feet with no elbows and 28 feet with four 90-degree elbows using a 4-inch hood. Source: Kenmore - Kenmore Elite Steam Dryer Use & Care Guide (796.8178/796.9178)
- Clean the lint trap after every load, since lint that gets past it builds up in the vent and lengthens drying times. Source: Kenmore - 3 Reasons to Clean Your Dryer Vent (And How to Do It)
Brand guides: Kenmore Dryer Not Heating: Causes and Fixes.
What Kenmore Dryer Repairs Cost
A Kenmore dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Thermal fuse repair: $80–$130 Source: Angi - How Much Does It Cost to Repair a Dryer?
- Gas valve coil replacement (gas dryer): $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Thermostat replacement: $100–$260 Source: Fixr - How much does it cost to repair a dryer?
- Drum belt replacement: $150–$250 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair: $100–$200 Source: Fixr - How much does it cost to repair a dryer?
- Technician service / diagnostic fee, dryer: $50–$80 per visit Source: Fixr - How much does it cost to repair a dryer?
A dryer that keeps needing repairs despite regular maintenance is usually cheaper to replace. Source: Angi - How Much Does Dryer Repair Cost?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
What to Have Ready for a Kenmore Dryer Call
- The brand, model and serial number from the label inside the door or on the back panel
- Whether the dryer is gas or electric
- Any error code on the display
What Burnsville Owners Should Know
Most dryer calls in Burnsville come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Minnesota has no state license for mechanical contractors or their workers; businesses contracting for gas, heating, cooling or refrigeration work file a mechanical contractor bond with the Department of Labor and Industry, and some cities require their own licenses or competency cards. Source: DLI: Mechanical contractor bond requirements
The state does not license gas fitters; contractors doing gas work must be bonded with the Department of Labor and Industry, and cities such as Minneapolis and St. Paul set their own gas fitter licensing. Source: DLI: Mechanical contractor bond requirements
Before You Book in Burnsville
- Do you work on gas dryers, and who handles anything involving the gas line?
- What is the service call or diagnostic fee, and is it applied to the repair?
- What guarantee do you give on parts and labor?
Kenmore Dryer Repair FAQs: Burnsville, MN
How do I find a technician who knows Kenmore dryers?
Is this Kenmore customer service?
Why does my dryer take so long to dry?
Why is my dryer running but not heating?
Other Dryer Repair in Burnsville
Kenmore Dryer Repair in Nearby Cities
Before you call, find the model and serial number on your Kenmore dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.