Most GE dryer repairs in St. Joseph involve the same few systems: heat, airflow, the drum drive and the controls. We flag companies whose listing or website mentions GE and fill in with nearby dryer repair companies so you always have options.
This is an independent directory. We are not affiliated with GE, and the technicians listed are independent repair companies, not the manufacturer.
GE Dryer Repair Near St. Joseph
Our data shows 12 appliance repair companies inside a 30-mile radius of St. Joseph. Other nearby bases include St Cloud (6), Sauk Rapids (2), and Richmond (1). The farthest listed company is about 29 miles out. No company within 30 miles of St. Joseph names GE in its listing, so the list adds matches from farther out and the closest appliance repair companies. Sears Appliance Repair is the nearest, roughly 4.8 miles from St. Joseph. The 12 rated companies in range average 4.7 stars.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| Mention GE | 0 |
|---|---|
| Open on Saturdays (per listing) | 7 |
| With 4.5+ stars and at least 10 reviews | 7 |
| Appliance repair companies in range (30 mi) | 12 |
| Three nearest companies, miles away | 4.8, 4.9, 5.6 |
| Show laundry appliance work | 4 |
At the top of the St. Joseph list: Sears Appliance Repair (47.5 miles away, based in Willmar, 4.5 stars from 37 reviews, lists Saturday hours); Crosstown Appliance Repair (12.8 miles away, based in Richmond, 4.8 stars from 154 reviews); Omega Force Appliance Repair (7.2 miles away, based in St Cloud, 4.8 stars from 199 reviews, lists Saturday hours); Sears Appliance Repair (4.8 miles away, based in St Cloud, 4.4 stars from 86 reviews, lists Saturday hours).
Know Your GE Dryer
How GE Dryers Are Built
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
The GE Profile UltraFast Combo uses a two-stage filter system (a mesh lint filter plus a second mesh or foam filter) located between the display and the dispenser drawers. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
GE Dryer Symptoms and First Checks
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
- Check Vent alert. GE says to unplug the dryer, disconnect and vacuum the duct, and make sure the outside hood damper moves freely. Source: GE Appliances - Dryer - Check Vent Sensor Alert
What GE Dryer Codes Mean
| Code | What it means |
|---|---|
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
Signs Your GE Dryer Needs a Technician
- Dryer will not start when you press Start
- Cycles take two or three runs to finish
- Dryer shuts off a few minutes into the cycle
Inside a Dryer Repair Visit
Keeping a GE Dryer Running
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
- Inspect and clean the exhaust duct at least once a year by unplugging the dryer, disconnecting the duct and vacuuming it, and check that the outside hood flaps move freely with no nests inside. Source: GE Appliances - Dryer - How to Clean Exhaust / Vent Duct
Brand guides: GE Dryer Not Heating: What to Check.
Budgeting for a GE Dryer Repair
A GE dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Thermal fuse repair: $80–$130 Source: Angi - How Much Does It Cost to Repair a Dryer?
- Control board (part only): $90–$280 Source: Angi - How Much Does Dryer Repair Cost?
- Drum belt replacement: $150–$250 Source: Fixr - How much does it cost to repair a dryer?
- Door switch replacement: $50–$150 Source: Fixr - How much does it cost to repair a dryer?
- Service call fee (may be waived if the technician does the repair): $50–$80 per visit Source: Angi - How Much Does It Cost to Repair a Dryer?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Before the Technician Arrives
- The brand, model and serial number from the label inside the door or on the back panel
- How long the vent run is and where it exits the house
- What happens when you press Start (no response, hum, runs with no heat, stops early)
What St. Joseph Owners Should Know
Most dryer calls in St. Joseph come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Minnesota has no state license for mechanical contractors or their workers; businesses contracting for gas, heating, cooling or refrigeration work file a mechanical contractor bond with the Department of Labor and Industry, and some cities require their own licenses or competency cards. Source: DLI: Mechanical contractor bond requirements
The state does not license gas fitters; contractors doing gas work must be bonded with the Department of Labor and Industry, and cities such as Minneapolis and St. Paul set their own gas fitter licensing. Source: DLI: Mechanical contractor bond requirements
Questions to Ask a St. Joseph Technician
- Is your company licensed where my state requires it, and insured?
- If a part has to be ordered, how soon can you come back to finish?
- What is the service call or diagnostic fee, and is it applied to the repair?
GE Dryer Repair FAQs: St. Joseph, MN
How do I find a technician who knows GE dryers?
Why do my clothes come out damp?
Is this GE customer service?
Why does my GE dryer show an error code?
Other Dryer Repair in St. Joseph
GE Dryer Repair Near St. Joseph
Write down any error code your GE dryer shows and when it appears. It helps a St. Joseph technician bring the right parts.