A GE dryer shares most of its parts with other dryers, but its controls, error codes and sensor-dry cycles are specific to the brand. The Little Falls list starts with companies that name GE, followed by other appliance repair companies that list dryer work.
Washer and Dryer Repair is independent and not affiliated with GE. Listed companies are independent technicians who repair GE dryers and other brands.
Independent GE Dryer Technicians, Little Falls MN
Our data shows 24 appliance repair companies inside a 60-mile radius of Little Falls. 1 list an address in Little Falls, and other nearby bases include St Cloud (6), Brainerd (5), and Sauk Rapids (2). None of the companies within 60 miles mention GE by name, so we include matching companies from a longer drive plus the nearest appliance repair companies. Nearest on the list: A-1 Appliance & Refrigeration., around 6.2 miles out. Across 24 rated companies, the average public rating is 4.7 stars. Little Falls is a smaller market, so expect a longer drive and ask whether a trip charge applies.
Companies are shown by relevance and distance from Little Falls. A mention does not mean manufacturer certification, so ask each company about its experience with your dryer.
| Mention GE | 0 |
|---|---|
| Repair companies inside 60 miles | 24 |
| Listing Saturday hours | 13 |
| Rated 4.5 stars or higher (10+ reviews) | 16 |
| Show laundry appliance work | 7 |
| Three nearest companies, miles away | 6.2, 24.1, 26.8 |
First up for Little Falls: Sears Appliance Repair (69.0 miles away, based in Willmar, 4.5 stars from 37 reviews, lists Saturday hours); Schroeder's Home Center (28.6 miles away, based in Brainerd, 4.9 stars from 754 reviews, lists Saturday hours); Crosstown Appliance Repair (37.6 miles away, based in Richmond, 4.8 stars from 154 reviews); Omega Force Appliance Repair (32.4 miles away, based in St Cloud, 4.8 stars from 199 reviews, lists Saturday hours).
GE Dryer Features Technicians Work On
What Makes GE Dryer Repairs Different
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Common GE Dryer Problems
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
- Dryer takes too long to dry. GE points first to venting (metal duct, no kinks, clear wall cap) and a clean lint filter, then to load size, dryer level and washer spin speed. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Reading a GE Dryer Error Code
| Code | What it means |
|---|---|
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
When to Call for GE Dryer Repair
- Squealing, thumping or grinding while it runs
- Clothes still damp after a full cycle
- Drum will not turn even though you hear a hum
What a Dryer Repair Technician Checks
Owner Care for GE Dryers
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
- Inspect and clean the exhaust duct at least once a year by unplugging the dryer, disconnecting the duct and vacuuming it, and check that the outside hood flaps move freely with no nests inside. Source: GE Appliances - Dryer - How to Clean Exhaust / Vent Duct
Brand guides: GE Dryer Not Heating: What to Check.
What GE Dryer Repairs Cost
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Drum bearing replacement: $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Thermostat replacement: $100–$260 Source: Fixr - How much does it cost to repair a dryer?
- Timer replacement: $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Door switch replacement: $50–$150 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair: $100–$200 Source: Fixr - How much does it cost to repair a dryer?
- Technician labor: $50–$100 per hour Source: Angi - How Much Does Dryer Repair Cost?
Replacement makes more sense once a dryer is about 10 years old or past half its expected lifespan. Source: Fixr - How much does it cost to repair a dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Getting Ready for the Repair
- The brand, model and serial number from the label inside the door or on the back panel
- What happens when you press Start (no response, hum, runs with no heat, stops early)
- Whether the dryer is gas or electric
What Little Falls Owners Should Know
Most dryer calls in Little Falls come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Minnesota has no state license for mechanical contractors or their workers; businesses contracting for gas, heating, cooling or refrigeration work file a mechanical contractor bond with the Department of Labor and Industry, and some cities require their own licenses or competency cards. Source: DLI: Mechanical contractor bond requirements
The state does not license gas fitters; contractors doing gas work must be bonded with the Department of Labor and Industry, and cities such as Minneapolis and St. Paul set their own gas fitter licensing. Source: DLI: Mechanical contractor bond requirements
Hiring a Dryer Repair Company in Little Falls
- How often do you repair GE dryers, and do you carry common parts on the truck?
- Is your company licensed where my state requires it, and insured?
- Do you work on gas dryers, and who handles anything involving the gas line?
GE Dryer Repair FAQs: Little Falls, MN
How do I find a technician who knows GE dryers?
Why do my clothes come out damp?
Why does my GE dryer show an error code?
Other Dryer Repair in Little Falls
GE Dryer Repair in Nearby Cities
Clean the lint screen, check the vent hood outside and note the model number before calling. It rules out the simple causes and speeds up a GE repair.