Most GE dryer repairs in Glendale involve the same few systems: heat, airflow, the drum drive and the controls. We flag companies whose listing or website mentions GE and fill in with nearby dryer repair companies so you always have options.
Independent listings only: Washer and Dryer Repair is not affiliated with or endorsed by GE. If your dryer is still under manufacturer coverage, contact GE directly.
Who Works on GE Dryers Near Glendale
Our data shows 40 appliance repair companies inside a 30-mile radius of Glendale. The rest are spread across Denver (29), Aurora (8), and Englewood (3). The farthest listed company is about 5 miles out. No company within 30 miles of Glendale names GE in its listing, so the list adds matches from farther out and the closest appliance repair companies. The closest is Wilson & Myers, about 0.9 miles away. Rated companies nearby average 4.7 stars across 35 businesses.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| Open on Saturdays (per listing) | 42 |
|---|---|
| Rated 4.5 stars or higher (10+ reviews) | 25 |
| Mention GE | 0 |
| Show laundry appliance work | 16 |
| Companies within 30 miles | 60 |
| Distance to the three closest (mi) | 0.9, 1.1, 1.4 |
At the top of the Glendale list: GE Monogram Repair Expert (20.5 miles away, based in Castle Rock, 4.9 stars from 91 reviews, lists Saturday hours); Mr. Appliance of Denver (1.4 miles away, based in Denver, 4.8 stars from 2,260 reviews, lists Saturday hours); Wilson & Myers (0.9 miles away, based in Denver, 4.9 stars from 1,412 reviews, lists Saturday hours); Mr. Appliance of Aurora (4.9 miles away, based in Aurora, 4.8 stars from 737 reviews).
Know Your GE Dryer
What a GE Dryer Technician Deals With
The GE Profile UltraFast Combo uses a two-stage filter system (a mesh lint filter plus a second mesh or foam filter) located between the display and the dispenser drawers. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
What GE Says to Check First
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
- Dryer takes too long to dry. GE points first to venting (metal duct, no kinks, clear wall cap) and a clean lint filter, then to load size, dryer level and washer spin speed. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
What GE Dryer Codes Mean
| Code | What it means |
|---|---|
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Squealing, thumping or grinding while it runs
- Burning or hot smell during a cycle
- Drum will not turn even though you hear a hum
What a Dryer Repair Technician Checks
Keeping a GE Dryer Running
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Brand guides: GE Dryer Not Heating: What to Check.
What GE Dryer Repairs Cost
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Heating element replacement: $150–$350 Source: Fixr - How much does it cost to repair a dryer?
- Control board (part only): $90–$280 Source: Angi - How Much Does Dryer Repair Cost?
- Igniter replacement (gas dryer): $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair (most homeowners): $100–$430 Source: Angi - How Much Does Dryer Repair Cost?
- Service call fee (may be waived if the technician does the repair): $50–$80 per visit Source: Angi - How Much Does It Cost to Repair a Dryer?
Replacement makes more sense once a dryer is about 10 years old or past half its expected lifespan. Source: Fixr - How much does it cost to repair a dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
What to Have Ready for a GE Dryer Call
- What happens when you press Start (no response, hum, runs with no heat, stops early)
- The brand, model and serial number from the label inside the door or on the back panel
- Whether the dryer is gas or electric
Around Glendale
Most dryer calls in Glendale come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Colorado's Division of Professions and Occupations has no appliance repair license; its trade licenses cover plumbing and electrical work. Source: Occupational Professions (Colorado DORA Division of Professions and Occupations)
In Colorado, you can check a license with the Colorado DORA License Lookup or report a problem to the Colorado Attorney General, Consumer Protection.
How to Choose a Dryer Technician Near Glendale
- What is the service call or diagnostic fee, and is it applied to the repair?
- Can you give a written estimate before ordering parts?
- Will you check the vent and lint path as part of the visit?
GE Dryer Repair FAQs: Glendale, CO
How do I find a technician who knows GE dryers?
Do you work for GE?
Why is my dryer running but not heating?
Should I repair or replace my GE dryer?
More Laundry Repair in Glendale, CO
GE Dryer Repair in Nearby Cities
Write down any error code your GE dryer shows and when it appears. It helps a Glendale technician bring the right parts.