A GE dryer shares most of its parts with other dryers, but its controls, error codes and sensor-dry cycles are specific to the brand. The Owings Mills list starts with companies that name GE, followed by other appliance repair companies that list dryer work.
Independent listings only: Washer and Dryer Repair is not affiliated with or endorsed by GE. If your dryer is still under manufacturer coverage, contact GE directly.
GE Dryer Repair Near Owings Mills
Our data shows 40 appliance repair companies inside a 30-mile radius of Owings Mills. 1 list an address in Owings Mills, and the rest are spread across Baltimore (15), Randallstown (3), and Towson (3). The farthest listed company is about 14 miles out. Town Appliance is the nearest, roughly 1.7 miles from Owings Mills. None of the companies within 30 miles mention GE by name, so we include matching companies from a longer drive plus the nearest appliance repair companies. Across 36 rated companies, the average public rating is 4.5 stars.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| Show laundry appliance work | 16 |
|---|---|
| Three nearest companies, miles away | 1.7, 2.3, 2.5 |
| Listing Saturday hours | 38 |
| Appliance repair companies in range (30 mi) | 60 |
| Mention GE | 0 |
| With 4.5+ stars and at least 10 reviews | 24 |
The leading options for Owings Mills are District-Columbia Hotpoint Rpr (37.9 miles away, based in Washington, 5.0 stars from 4 reviews, lists Saturday hours); Mr. Appliance of Howard County (9.5 miles away, based in Ellicott City, 4.7 stars from 1,049 reviews, lists Saturday hours); NT Appliances Repair Service (2.3 miles away, based in Randallstown, 4.9 stars from 83 reviews, lists Saturday hours); All-Star Appliance Repair Baltimore (7.1 miles away, based in Baltimore, 4.7 stars from 1,459 reviews, lists Saturday hours).
Know Your GE Dryer
What Makes GE Dryer Repairs Different
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
Common GE Dryer Problems
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
- Dryer will not run or start. GE's first check is that the dryer plug is pushed fully into the wall outlet. Source: GE Appliances - Dryer - Will Not Run or Start
GE Dryer Error Codes
| Code | What it means |
|---|---|
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
When to Call for GE Dryer Repair
- Clothes still damp after a full cycle
- Drum turns but the air stays cool
- Dryer shuts off a few minutes into the cycle
Inside a Dryer Repair Visit
Care GE Recommends for Its Dryers
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Brand guides: GE Dryer Not Heating: What to Check.
GE Dryer Repair Cost Ranges
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Gas valve coil replacement (gas dryer): $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Thermostat replacement: $100–$260 Source: Fixr - How much does it cost to repair a dryer?
- Door switch replacement: $50–$150 Source: Fixr - How much does it cost to repair a dryer?
- Thermal fuse repair: $80–$130 Source: Angi - How Much Does It Cost to Repair a Dryer?
- Typical dryer repair (most homeowners): $100–$430 Source: Angi - How Much Does Dryer Repair Cost?
- Technician service / diagnostic fee, dryer: $50–$80 per visit Source: Fixr - How much does it cost to repair a dryer?
If a repair would cost more than about half the price of a new dryer, replacing is usually the better choice. Source: Angi - How Much Does It Cost to Repair a Dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Before the Technician Arrives
- Whether the dryer is gas or electric
- Any error code on the display
- The brand, model and serial number from the label inside the door or on the back panel
What Owings Mills Owners Should Know
Most dryer calls in Owings Mills come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Maryland does not issue a separate appliance repair license; the Maryland Board of Plumbing licenses plumbers, natural gas fitters and propane gas fitters, whose trades cover gas connections. Source: License Requirements - Maryland Board of Plumbing (Maryland Department of Labor)
The Maryland Board of Plumbing issues master, journey and apprentice natural gas fitter licenses and a propane gas fitter certificate, and recognizes certain Baltimore County and WSSC gas fitter licenses. Source: Md. Code, Business Occupations and Professions ยง 12-302 (Maryland General Assembly)
Questions to Ask a Owings Mills Technician
- Can you give a written estimate before ordering parts?
- What guarantee do you give on parts and labor?
- If a part has to be ordered, how soon can you come back to finish?
GE Dryer Repair FAQs: Owings Mills, MD
Is my GE dryer worth repairing?
How do I find a technician who knows GE dryers?
Is this GE customer service?
What makes a dryer stop heating?
Related Repair Pages for Owings Mills
GE Dryer Repair in Nearby Cities
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.