A GE dryer shares most of its parts with other dryers, but its controls, error codes and sensor-dry cycles are specific to the brand. Below are independent repair companies serving Rogers, with those that mention GE first, then the nearest dryer repair companies.
Independent listings only: Washer and Dryer Repair is not affiliated with or endorsed by GE. If your dryer is still under manufacturer coverage, contact GE directly.
Who Works on GE Dryers Near Rogers
40 repair companies serve Rogers from within 30 miles. 2 of them are based in Rogers itself, and other nearby bases include Blaine (5), Plymouth (4), and Wayzata (3). No company within 30 miles of Rogers names GE in its listing, so the list adds matches from farther out and the closest appliance repair companies. Nearest on the list: Omega Force Appliance Repair, around 1.3 miles out. Rated companies nearby average 4.5 stars across 22 businesses.
Companies are shown by relevance and distance from Rogers. A mention does not mean manufacturer certification, so ask each company about its experience with your dryer.
| With 4.5+ stars and at least 10 reviews | 17 |
|---|---|
| Show laundry appliance work | 11 |
| Companies within 30 miles | 60 |
| Three nearest companies, miles away | 1.3, 1.8, 4.6 |
| Open on Saturdays (per listing) | 45 |
| Mention GE | 0 |
The leading options for Rogers are Sears Appliance Repair (71.5 miles away, based in Willmar, 4.5 stars from 37 reviews, lists Saturday hours); Omega Force Appliance Repair (1.3 miles away, 4.9 stars from 1,637 reviews, lists Saturday hours); Anderson's Mechanical Services LLC (17.0 miles away, based in Blaine, 4.8 stars from 1,207 reviews, lists Saturday hours); Appliance Solutions (17.7 miles away, based in Ham Lake, 4.4 stars from 440 reviews, lists Saturday hours).
GE Dryer Features Technicians Work On
What a GE Dryer Technician Deals With
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
What GE Says to Check First
- Dryer takes too long to dry. GE points first to venting (metal duct, no kinks, clear wall cap) and a clean lint filter, then to load size, dryer level and washer spin speed. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
What GE Dryer Codes Mean
| Code | What it means |
|---|---|
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
Signs Your GE Dryer Needs a Technician
- Dryer shuts off a few minutes into the cycle
- Dryer will not start when you press Start
- Squealing, thumping or grinding while it runs
How a Dryer Service Call Usually Goes in Rogers
Keeping a GE Dryer Running
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Brand guides: GE Dryer Not Heating: What to Check.
GE Dryer Repair Cost Ranges
A GE dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Control board (part only): $90–$280 Source: Angi - How Much Does Dryer Repair Cost?
- Drum belt replacement: $150–$250 Source: Fixr - How much does it cost to repair a dryer?
- Drum roller replacement: $100–$150 Source: Fixr - How much does it cost to repair a dryer?
- Appliance technician diagnosis, washer (usually waived if hired for the repair): $50–$100 per visit Source: Fixr - How much does it cost to repair a washing machine?
Replacement makes more sense once a dryer is about 10 years old or past half its expected lifespan. Source: Fixr - How much does it cost to repair a dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Getting Ready for the Repair
- Any error code on the display
- How long the vent run is and where it exits the house
- The brand, model and serial number from the label inside the door or on the back panel
What Rogers Owners Should Know
Most dryer calls in Rogers come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Minnesota has no state license for mechanical contractors or their workers; businesses contracting for gas, heating, cooling or refrigeration work file a mechanical contractor bond with the Department of Labor and Industry, and some cities require their own licenses or competency cards. Source: DLI: Mechanical contractor bond requirements
In Minnesota, you can check a license with the DLI License and Registration Lookup or report a problem to the Minnesota Attorney General's Office, Consumer Assistance.
Questions to Ask a Rogers Technician
- What is the service call or diagnostic fee, and is it applied to the repair?
- Is your company licensed where my state requires it, and insured?
- Will you check the vent and lint path as part of the visit?
GE Dryer Repair FAQs: Rogers, MN
Why does my dryer take so long to dry?
Should I repair or replace my GE dryer?
Do you work for GE?
Why is my dryer running but not heating?
Related Repair Pages for Rogers
GE Dryer Repair in Nearby Cities
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.