If your GE dryer has stopped heating, stopped tumbling or started throwing an error code, the technician you call should know the model line. The Roseville list starts with companies that name GE, followed by other appliance repair companies that list dryer work.
This is an independent directory. We are not affiliated with GE, and the technicians listed are independent repair companies, not the manufacturer.
Independent GE Dryer Technicians, Roseville MN
Our data shows 40 appliance repair companies inside a 30-mile radius of Roseville. 1 of them are based in Roseville itself, and the rest are spread across St Paul (11), Minneapolis (11), and Maplewood (4). Distances run up to about 10 miles. Appliance Repair Station is the nearest, roughly 1.3 miles from Roseville. None of the repair companies near Roseville name GE in their listings, so we show the closest appliance repair companies. Ask each one about your model before booking. Rated companies nearby average 4.4 stars across 25 businesses.
Companies are shown by relevance and distance from Roseville. A mention does not mean manufacturer certification, so ask each company about its experience with your dryer.
| Mention GE | 0 |
|---|---|
| Three nearest companies, miles away | 1.3, 1.7, 2.7 |
| List dryer or washer & dryer work | 13 |
| Rated 4.5 stars or higher (10+ reviews) | 22 |
| Open on Saturdays (per listing) | 49 |
| Appliance repair companies in range (30 mi) | 60 |
The leading options for Roseville are Warners' Stellian Appliance (1.7 miles away, based in St Paul, 4.8 stars from 2,260 reviews, lists Saturday hours); Omega Force Appliance Repair (4.3 miles away, based in St Paul, 4.9 stars from 678 reviews, lists Saturday hours); Super Care Appliance Repair (8.7 miles away, based in West St Paul, 4.9 stars from 1,075 reviews, lists Saturday hours); Warners' Stellian Appliance Outlet (3.6 miles away, based in Minneapolis, 4.7 stars from 670 reviews, lists Saturday hours).
GE Dryer Features Technicians Work On
How GE Dryers Are Built
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Common GE Dryer Problems
- Gas dryer runs but does not heat. GE says to confirm a real drying cycle and temperature are selected, keep the front of the dryer unblocked, check the dedicated 120V outlet, and on new installs make sure the gas line is turned on. Source: GE Appliances - Gas Dryer - Runs But Does Not Heat
- Dryer takes too long to dry. GE points first to venting (metal duct, no kinks, clear wall cap) and a clean lint filter, then to load size, dryer level and washer spin speed. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Reading a GE Dryer Error Code
| Code | What it means |
|---|---|
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Drum turns but the air stays cool
- Cycles take two or three runs to finish
- Burning or hot smell during a cycle
What a Dryer Repair Technician Checks
Owner Care for GE Dryers
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
Brand guides: GE Dryer Not Heating: What to Check.
What GE Dryer Repairs Cost
A GE dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Igniter replacement (gas dryer): $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Gas valve coil replacement (gas dryer): $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Thermal fuse repair: $80–$130 Source: Angi - How Much Does It Cost to Repair a Dryer?
- Drum roller replacement: $100–$150 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair: $100–$200 Source: Fixr - How much does it cost to repair a dryer?
- Technician labor: $50–$100 per hour Source: Angi - How Much Does Dryer Repair Cost?
A dryer that keeps needing repairs despite regular maintenance is usually cheaper to replace. Source: Angi - How Much Does Dryer Repair Cost?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Getting Ready for the Repair
- The brand, model and serial number from the label inside the door or on the back panel
- Whether the dryer is gas or electric
- Any error code on the display
Around Roseville
Most dryer calls in Roseville come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Minnesota has no state license for mechanical contractors or their workers; businesses contracting for gas, heating, cooling or refrigeration work file a mechanical contractor bond with the Department of Labor and Industry, and some cities require their own licenses or competency cards. Source: DLI: Mechanical contractor bond requirements
The state does not license gas fitters; contractors doing gas work must be bonded with the Department of Labor and Industry, and cities such as Minneapolis and St. Paul set their own gas fitter licensing. Source: DLI: Mechanical contractor bond requirements
Hiring a Dryer Repair Company in Roseville
- Will you check the vent and lint path as part of the visit?
- Can you give a written estimate before ordering parts?
- What guarantee do you give on parts and labor?
GE Dryer Repair FAQs: Roseville, MN
Why is my dryer running but not heating?
Is this GE customer service?
Why does my dryer take so long to dry?
Why does my GE dryer show an error code?
Related Repair Pages for Roseville
GE Dryer Repair Near Roseville
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.