GE owners in St. Peter usually want two things from a repair company: experience with the brand and quick access to parts. The St. Peter list starts with companies that name GE, followed by other appliance repair companies that list dryer work.
This is an independent directory. We are not affiliated with GE, and the technicians listed are independent repair companies, not the manufacturer.
Independent GE Dryer Technicians, St. Peter MN
We found 12 appliance repair companies within 30 miles of St. Peter. The rest are spread across Mankato (5), New Ulm (3), and Waseca (2). Distances run up to about 28 miles. No company within 30 miles of St. Peter names GE in its listing, so the list adds matches from farther out and the closest appliance repair companies. The closest is Don's Appliance & TV of Minnesota, about 0.9 miles away. The 11 rated companies in range average 4.4 stars.
Listings come from public business data. A brand or service mention means the company names it in its listing or website; it is not a certification. Verify experience, licensing and insurance before hiring.
| Listing Saturday hours | 7 |
|---|---|
| Show laundry appliance work | 2 |
| Three nearest companies, miles away | 0.9, 10.3, 11.0 |
| Repair companies inside 30 miles | 12 |
| With 4.5+ stars and at least 10 reviews | 7 |
| Mention GE | 0 |
Closest matches for St. Peter: Sears Appliance Repair (75.2 miles away, based in Willmar, 4.5 stars from 37 reviews, lists Saturday hours); Don's Appliance & TV of Minnesota (0.9 miles away, based in St Peter, 3.8 stars from 67 reviews, lists Saturday hours); Sears Appliance Repair (23.8 miles away, based in New Ulm, 4.7 stars from 41 reviews, lists Saturday hours); Degrood's Appliance (10.3 miles away, based in Mankato, 4.7 stars from 251 reviews, lists Saturday hours).
GE Dryer Lines and Features
How GE Dryers Are Built
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
GE Dryer Symptoms and First Checks
- Check Vent alert. GE says to unplug the dryer, disconnect and vacuum the duct, and make sure the outside hood damper moves freely. Source: GE Appliances - Dryer - Check Vent Sensor Alert
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
Reading a GE Dryer Error Code
| Code | What it means |
|---|---|
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
Signs Your GE Dryer Needs a Technician
- Clothes still damp after a full cycle
- Drum turns but the air stays cool
- Outside of the cabinet gets unusually hot
How a Dryer Service Call Usually Goes in St. Peter
Care GE Recommends for Its Dryers
- Inspect and clean the exhaust duct at least once a year by unplugging the dryer, disconnecting the duct and vacuuming it, and check that the outside hood flaps move freely with no nests inside. Source: GE Appliances - Dryer - How to Clean Exhaust / Vent Duct
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Brand guides: GE Dryer Not Heating: What to Check.
Budgeting for a GE Dryer Repair
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Igniter replacement (gas dryer): $100–$250 Source: Fixr - How much does it cost to repair a dryer?
- Drive motor replacement: $250–$450 Source: Fixr - How much does it cost to repair a dryer?
- Door switch replacement: $50–$150 Source: Fixr - How much does it cost to repair a dryer?
- Dryer not heating (repair by symptom): $80–$420 Source: Angi - How Much Does Dryer Repair Cost?
- Technician service / diagnostic fee, dryer: $50–$80 per visit Source: Fixr - How much does it cost to repair a dryer?
A dryer that keeps needing repairs despite regular maintenance is usually cheaper to replace. Source: Angi - How Much Does Dryer Repair Cost?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
Before the Technician Arrives
- The brand, model and serial number from the label inside the door or on the back panel
- What happens when you press Start (no response, hum, runs with no heat, stops early)
- How long the vent run is and where it exits the house
What St. Peter Owners Should Know
Most dryer calls in St. Peter come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Minnesota has no state license for mechanical contractors or their workers; businesses contracting for gas, heating, cooling or refrigeration work file a mechanical contractor bond with the Department of Labor and Industry, and some cities require their own licenses or competency cards. Source: DLI: Mechanical contractor bond requirements
The state does not license gas fitters; contractors doing gas work must be bonded with the Department of Labor and Industry, and cities such as Minneapolis and St. Paul set their own gas fitter licensing. Source: DLI: Mechanical contractor bond requirements
Hiring a Dryer Repair Company in St. Peter
- How often do you repair GE dryers, and do you carry common parts on the truck?
- If a part has to be ordered, how soon can you come back to finish?
- Can you give a written estimate before ordering parts?
GE Dryer Repair FAQs: St. Peter, MN
Why is my dryer running but not heating?
Why does my GE dryer show an error code?
Which St. Peter technicians work on GE?
Should I repair or replace my GE dryer?
Related Repair Pages for St. Peter
More GE Dryer Repair Pages Nearby
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.