A GE dryer shares most of its parts with other dryers, but its controls, error codes and sensor-dry cycles are specific to the brand. The Farmington list starts with companies that name GE, followed by other appliance repair companies that list dryer work.
This is an independent directory. We are not affiliated with GE, and the technicians listed are independent repair companies, not the manufacturer.
GE Dryer Repair Near Farmington
Within 60 miles of Farmington there are 11 appliance repair companies in our data. 3 of them are based in Farmington itself, and other nearby bases include Durango (6), Bayfield (1), and Cortez (1). None of the repair companies near Farmington name GE in their listings, so we show the closest appliance repair companies. Ask each one about your model before booking. Sears Appliance Repair is the nearest, roughly 1.8 miles from Farmington. Across 11 rated companies, the average public rating is 4.2 stars. Farmington is a smaller market, so expect a longer drive and ask whether a trip charge applies.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| Appliance repair companies in range (60 mi) | 11 |
|---|---|
| Show laundry appliance work | 3 |
| Distance to the three closest (mi) | 1.8, 2.6, 2.7 |
| Open on Saturdays (per listing) | 6 |
| Rated 4.5 stars or higher (10+ reviews) | 5 |
| Mention GE | 0 |
First up for Farmington: Sears Appliance Repair (1.8 miles away, 3.3 stars from 49 reviews, lists Saturday hours); Sears Appliance Repair (37.8 miles away, based in Durango, 5.0 stars from 3 reviews, lists Saturday hours); Appliance Service Co.. (2.7 miles away, 4.5 stars from 15 reviews); Star Tech Appliance LLC. (2.6 miles away, 4.3 stars from 17 reviews, lists Saturday hours).
GE Dryer Lines and Features
What Makes GE Dryer Repairs Different
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
Common GE Dryer Problems
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
- Check Vent alert. GE says to unplug the dryer, disconnect and vacuum the duct, and make sure the outside hood damper moves freely. Source: GE Appliances - Dryer - Check Vent Sensor Alert
Reading a GE Dryer Error Code
| Code | What it means |
|---|---|
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Clothes still damp after a full cycle
- Dryer shuts off a few minutes into the cycle
- Dryer will not start when you press Start
What a Dryer Repair Technician Checks
Care GE Recommends for Its Dryers
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Brand guides: GE Dryer Not Heating: What to Check.
Budgeting for a GE Dryer Repair
A GE dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Timer replacement: $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Gas valve coil replacement (gas dryer): $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Drum belt replacement: $150–$250 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair (most homeowners): $100–$430 Source: Angi - How Much Does Dryer Repair Cost?
- Service call fee (may be waived if the technician does the repair): $50–$80 per visit Source: Angi - How Much Does It Cost to Repair a Dryer?
Replacement makes more sense once a dryer is about 10 years old or past half its expected lifespan. Source: Fixr - How much does it cost to repair a dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
What to Have Ready for a GE Dryer Call
- How long the vent run is and where it exits the house
- Any error code on the display
- What happens when you press Start (no response, hum, runs with no heat, stops early)
Around Farmington
Most dryer calls in Farmington come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
New Mexico has no appliance-repair-only license; installing, repairing and servicing natural gas piping and listed gas appliances falls under the Construction Industries Division's MM-2 natural gas fitting classification. Source: CID License Classifications and Scopes (City of Albuquerque)
Natural gas piping and gas appliance work needs a Construction Industries Division MM-2 (natural gas fitting) or MM-98 (mechanical) license, with journeyman gas fitter certification for workers; the plumbing-only MM-1 class excludes gas appliances and gas piping, and LP gas systems fall under a separate LP gas classification. Source: CID License Classifications and Scopes (City of Albuquerque)
Before You Book in Farmington
- Will you check the vent and lint path as part of the visit?
- What guarantee do you give on parts and labor?
- If a part has to be ordered, how soon can you come back to finish?
GE Dryer Repair FAQs: Farmington, NM
Why do my clothes come out damp?
Do you work for GE?
How do I find a technician who knows GE dryers?
Related Repair Pages for Farmington
GE Dryer Repair Near Farmington
Clean the lint screen, check the vent hood outside and note the model number before calling. It rules out the simple causes and speeds up a GE repair.