If your GE dryer has stopped heating, stopped tumbling or started throwing an error code, the technician you call should know the model line. The Silver Springs list starts with companies that name GE, followed by other appliance repair companies that list dryer work.
Washer and Dryer Repair is independent and not affiliated with GE. Listed companies are independent technicians who repair GE dryers and other brands.
GE Dryer Repair Near Silver Springs
Within 60 miles of Silver Springs there are 33 appliance repair companies in our data. The rest are spread across Reno (15), Sparks (5), and Carson City (5). Distances run up to about 54 miles. 1 lists GE specifically. Nearest on the list: Smart Tech Appliance Repair, around 27.8 miles out. Rated companies nearby average 4.3 stars across 26 businesses. Silver Springs is a smaller market, so expect a longer drive and ask whether a trip charge applies.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| Mention GE | 1 |
|---|---|
| With 4.5+ stars and at least 10 reviews | 14 |
| Open on Saturdays (per listing) | 22 |
| List dryer or washer & dryer work | 12 |
| Distance to the three closest (mi) | 27.8, 29.0, 29.8 |
| Repair companies inside 60 miles | 33 |
First up for Silver Springs: Sears Appliance Repair (53.6 miles away, based in South Lake Tahoe, 4.5 stars from 60 reviews, lists Saturday hours); Mr. Appliance of Reno (31.5 miles away, based in Reno, 4.8 stars from 925 reviews, lists Saturday hours); Northern Nevada Appliance Outlet (34.2 miles away, based in Carson City, 4.5 stars from 292 reviews, lists Saturday hours); Sears Appliance Repair (31.8 miles away, based in Sparks, 4.7 stars from 124 reviews, lists Saturday hours).
GE Dryer Lines and Features
What a GE Dryer Technician Deals With
An electric GE dryer receiving only partial (120V) power from its 240V circuit can tumble normally but produce no heat, and a dryer wired to a 120V circuit can take up to three times longer to dry. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
GE Dryer Symptoms and First Checks
- Dryer hot to the touch or sweating. GE says this usually means heat and humidity cannot escape, so clean the exhaust duct, clear the wall cap and confirm the elbow count suits the vent length. Source: GE Appliances - Dryer - Hot to the Touch or Sweats
- Gas dryer runs but does not heat. GE says to confirm a real drying cycle and temperature are selected, keep the front of the dryer unblocked, check the dedicated 120V outlet, and on new installs make sure the gas line is turned on. Source: GE Appliances - Gas Dryer - Runs But Does Not Heat
Reading a GE Dryer Error Code
| Code | What it means |
|---|---|
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 353 (UltraFast Combo) | The lint filter is likely clogged, often with fabric softener residue; cleaning the filter clears it. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
GE Dryer Problems Worth a Service Call
- Squealing, thumping or grinding while it runs
- Outside of the cabinet gets unusually hot
- Dryer shuts off a few minutes into the cycle
How a Dryer Service Call Usually Goes in Silver Springs
Keeping a GE Dryer Running
- Clean the lint filter before every load and periodically wash it in warm soapy water to remove fabric softener film. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
- GE does not state one maximum vent length on its support pages; it says to follow the model's installation instructions for allowed duct length and number of elbows, and recommends a 4-inch outside wall cap. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Brand guides: GE Dryer Not Heating: What to Check.
Budgeting for a GE Dryer Repair
A GE dryer repair usually costs about the same as any other brand for the same part. Published ranges:
- Timer replacement: $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Drive motor replacement: $250–$450 Source: Fixr - How much does it cost to repair a dryer?
- Thermostat replacement: $100–$260 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair (most homeowners): $100–$430 Source: Angi - How Much Does Dryer Repair Cost?
- Technician labor: $50–$100 per hour Source: Angi - How Much Does Dryer Repair Cost?
A dryer that keeps needing repairs despite regular maintenance is usually cheaper to replace. Source: Angi - How Much Does Dryer Repair Cost?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
What to Have Ready for a GE Dryer Call
- What happens when you press Start (no response, hum, runs with no heat, stops early)
- Any error code on the display
- How long the vent run is and where it exits the house
What Silver Springs Owners Should Know
Most dryer calls in Silver Springs come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Nevada has no license class for appliance repair as such; contracting work on gas piping, gas vents and water heaters falls under the State Contractors Board's C-1 plumbing and heating subclassifications. Source: Nevada Administrative Code Chapter 624 (NAC 624.190)
Installing gas supply piping and vents requires a Nevada State Contractors Board license in the C-1 plumbing and heating classification (for example the C-1d plumbing or C-1g gas pipes and vents subclassifications), and water heater installation and repair falls under subclassification C-1h. Source: Nevada Administrative Code Chapter 624 (NAC 624.190)
Hiring a Dryer Repair Company in Silver Springs
- Will you check the vent and lint path as part of the visit?
- What is the service call or diagnostic fee, and is it applied to the repair?
- Is your company licensed where my state requires it, and insured?
GE Dryer Repair FAQs: Silver Springs, NV
How do I find a technician who knows GE dryers?
Do you work for GE?
Why does my dryer take so long to dry?
More Laundry Repair in Silver Springs, NV
More GE Dryer Repair Pages Nearby
Write down any error code your GE dryer shows and when it appears. It helps a Silver Springs technician bring the right parts.