Most GE dryer repairs in Bend involve the same few systems: heat, airflow, the drum drive and the controls. Below are independent repair companies serving Bend, with those that mention GE first, then the nearest dryer repair companies.
Independent listings only: Washer and Dryer Repair is not affiliated with or endorsed by GE. If your dryer is still under manufacturer coverage, contact GE directly.
Independent GE Dryer Technicians, Bend OR
Our data shows 12 appliance repair companies inside a 30-mile radius of Bend. 8 of them are based in Bend itself, and other nearby bases include Redmond (2) and Prineville (2). Nearest on the list: Mitchell's Appliance Repair Experts, around 0.3 miles out. None of the companies within 30 miles mention GE by name, so we include matching companies from a longer drive plus the nearest appliance repair companies. Across 11 rated companies, the average public rating is 4.3 stars.
We do not show business phone numbers. Call our helpline to be connected with a participating technician, or look a company up directly. Always confirm licensing and insurance.
| Three nearest companies, miles away | 0.3, 0.4, 1.0 |
|---|---|
| Rated 4.5 stars or higher (10+ reviews) | 4 |
| Show laundry appliance work | 6 |
| Mention GE | 0 |
| Listing Saturday hours | 6 |
| Companies within 30 miles | 12 |
The leading options for Bend are Sears Appliance Repair (40.5 miles away, based in Madras, lists Saturday hours); CORTech Services LLC. (1.3 miles away, 4.6 stars from 297 reviews); Oregon Appliance Repair (0.4 miles away, 3.9 stars from 369 reviews, lists Saturday hours); Polished Appliance Repair - Serving Central Oregon, Medford, and Eugene (17.6 miles away, based in Redmond, 4.5 stars from 261 reviews).
Know Your GE Dryer
What a GE Dryer Technician Deals With
Sensor dry models must sit level so tumbling clothes contact the moisture sensors; an unlevel dryer can end cycles with clothes still damp. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
GE allows only rigid or flexible metal vent duct and says plastic flexible duct is not acceptable because it collapses, cuts airflow and can collect water. Source: GE Appliances - Dryer - Things To Check For A Venting Issue
Common GE Dryer Problems
- Electric dryer runs but does not heat. GE says to confirm the dryer has a dedicated 240V supply, reset the breaker fully off and on, and then inspect the power cord and terminal block for burned or loose connections. Source: GE Appliances - Electric Dryer - Runs But Does Not Heat
- Dryer takes too long to dry. GE points first to venting (metal duct, no kinks, clear wall cap) and a clean lint filter, then to load size, dryer level and washer spin speed. Source: GE Appliances - Dryer - Taking Too Long To Dry Clothes or Not Drying at All
What GE Dryer Codes Mean
| Code | What it means |
|---|---|
| Check and Clean Drain Pump Filter (UltraFast Combo) | A restriction, often a loose item, was detected in the drain area and the pump filter should be cleaned. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| Confirm H2O Supply is ON (UltraFast Combo) | No water is entering the unit; controls lock for a few minutes while you check the water supply valves. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
| 18 (UltraFast Combo) | The drain pump filter needs cleaning; loads may also come out wet or take longer to dry, and the drain hose should not be pushed too far into the standpipe. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Fault & Error Codes and Status Messages |
When to Call for GE Dryer Repair
- Dryer shuts off a few minutes into the cycle
- Outside of the cabinet gets unusually hot
- Clothes still damp after a full cycle
Inside a Dryer Repair Visit
Care GE Recommends for Its Dryers
- On the UltraFast Combo, clean the mesh lint filter about every fifth dry cycle or when prompted, and clean the foam filter and filter compartment about every 50 cycles. Source: GE Appliances - GE Profile UltraFast Combo Washer/Dryer - Filter Cleaning
- Inspect and clean the exhaust duct at least once a year by unplugging the dryer, disconnecting the duct and vacuuming it, and check that the outside hood flaps move freely with no nests inside. Source: GE Appliances - Dryer - How to Clean Exhaust / Vent Duct
Brand guides: GE Dryer Not Heating: What to Check.
What GE Dryer Repairs Cost
Most GE dryer repairs involve common parts and an hour or so of labor. For reference, published cost guides report:
- Control board (part only): $90–$280 Source: Angi - How Much Does Dryer Repair Cost?
- Timer replacement: $150–$300 Source: Fixr - How much does it cost to repair a dryer?
- Door switch replacement: $50–$150 Source: Fixr - How much does it cost to repair a dryer?
- Thermostat replacement: $100–$260 Source: Fixr - How much does it cost to repair a dryer?
- Typical dryer repair (most homeowners): $100–$430 Source: Angi - How Much Does Dryer Repair Cost?
- Appliance technician diagnosis, washer (usually waived if hired for the repair): $50–$100 per visit Source: Fixr - How much does it cost to repair a washing machine?
Replacement makes more sense once a dryer is about 10 years old or past half its expected lifespan. Source: Fixr - How much does it cost to repair a dryer?
Ranges are published estimates, not quotes. See the dryer repair cost guide and how long dryers last.
What to Have Ready for a GE Dryer Call
- Any error code on the display
- Whether the dryer is gas or electric
- How long the vent run is and where it exits the house
Dryer Notes for Bend, OR
Most dryer calls in Bend come down to the same handful of parts: the vent and lint path, the heat source, the belt and rollers, and the door and start switches.
Oregon has no license issued specifically for appliance repair that we could confirm, but anyone installing or servicing liquefied petroleum (LP) gas appliances needs an LP gas fitter license from the Oregon State Fire Marshal. Source: Liquefied Petroleum Gas licensing (Oregon State Fire Marshal)
Businesses that install, alter or repair LP gas appliances, piping or vent connections need an LP gas installation license, and the individuals doing the work need a fitter license, both from the Oregon State Fire Marshal; natural gas licensing was not confirmed. Source: Liquefied Petroleum Gas licensing (Oregon State Fire Marshal)
Before You Book in Bend
- How often do you repair GE dryers, and do you carry common parts on the truck?
- What guarantee do you give on parts and labor?
- What is the service call or diagnostic fee, and is it applied to the repair?
GE Dryer Repair FAQs: Bend, OR
Do you work for GE?
Why is my dryer running but not heating?
Why does my GE dryer show an error code?
How do I find a technician who knows GE dryers?
More Laundry Repair in Bend, OR
GE Dryer Repair Near Bend
Before you call, find the model and serial number on your GE dryer's label, usually inside the door opening. A technician who knows the model can often tell you on the phone what the first visit will involve.